- 您現在的位置：買賣IC網 > PDF目錄376151 > MC1451A-E (Electronic Theatre Controls, Inc.) Advanced Brushless Motor Control Chipset PDF資料下載
參數資料
| 型號： | MC1451A-E |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Advanced Brushless Motor Control Chipset |
| 中文描述： | 先進的無刷電機控制芯片組 |
| 文件頁數： | 47/70頁 |
| 文件大?。?/td> | 474K |
| 代理商： | MC1451A-E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
47
SET_I_LM
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set integration limit
1/write
28 (hex)
current axis
all axes
yes
SET_I_LMsets the integration limt for the digital filter. The integration
limt is specified as an unsigned 16-bit number. The range is 0 to
32,767. The loaded integration limt is not utilized until a parameter
update occurs.
SET_MTR_LMT
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set motor output limit
1/write
06 (hex)
current axis
all axes
no
SET_MTR_LMT sets the maximumallowed motor command value
output by the servo filter. The motor limt is specified as an unsigned
16-bit number with a range of 0 to 32,767. If the magnitude of the filter
output value (whether positive or negative) exceeds the motor limt than
the output value is maintained at the motor limt value. Once the filter
output value returns below the specified limt than normal servo filter
values are output.
The loaded motor output limit is utilized immediately. No UPDATE
command is required.
The SET_MTR_LMT command only functions during closed loop
operations.
SET_MTR_BIAS
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set motor output bias
1/write
0f (hex)
current axis
all axes
no
SET_MTR_BIAS sets the filter DC bias value, used to offset constant
uni-directional forces (typically a vertical axis which is not balanced by a
counter-weight). The specified motor bias value is added directly to the
output of the servo filter. The motor bias is specified as a signed 16-bit
number with a range of -32,767 to 32,767.
The loaded motor bias value is utilized immediately. No UPDATE
command is required.
The SET_MTR_BIAS command functions during closed loop
operations, as well as after a transition to open loop before a
SET_MTR_CMD manual motor output command has been given.
Caution should be used when selecting a motor bias value to
avoid uncontrolled axis motion when transitioning to open loop
mode.
SET_POS_ERR
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set position error limit
1/write
29 (hex)
current axis
all axes
no
SET_POS_ERR sets the position error limt for the digital filter. The
error is specified as an unsigned 16-bit number. The range is 0 to
32,767. At each servo loop the magnitude of the position error
calculated by the digital filter is compared with the specified position
error limt. If the actual position error exceeds the specified value, the
motion error interrupt bit is set. In addition, if the axis has been set for
automatic motor stop upon motion error, the axis motor output may be
turned off (all power to motor is turned off). The loaded maximum
position error is utilized immediately.
The value set by this command specifies the limit of the valid
motion error range, but not necessarily the maximum error value.
If the position error limit value is set to less than 32,767 than the
actual position error may exceed the specified limit.
GET_KP
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Get proportional gain
1/read
50 (hex)
current axis
all axes
-
GET_KP returns the proportional gain set using the SET_KP command.
It returns the double-buffered value (set directly by the host), which may
or may not correspond to the active value, depending on whether the
filter parameters have been updated. The returned gain value is an
unsigned 16-bit number.
GET_KD
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Get derivative gain
1/read
52 (hex)
current axis
all axes
-
GET_KD returns the derivative gain set using the SET_KD command. It
returns the double-buffered value (set directly by the host), which may
or may not correspond to the active value, depending on whether the
filter parameters have been updated. The returned gain value is an
unsigned 16-bit number.
相關PDF資料 |
PDF描述 |
|---|---|
| MC1101A-P | Advanced Brushless Motor Control Chipset |
| MC1211N | LSI CMOS |
| MCY1210N | LSI CMOS |
| MC14005N | 8-function calculator unit co-operating with LED display |
| MC74005N | 8-function calculator unit co-operating with LED display |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1451CCP | 制造商:PMD 功能描述: |
| MC14520B | 制造商:Motorola Inc 功能描述: 制造商:ON Semiconductor 功能描述: |
| MC14520BAL | 制造商:Motorola Inc 功能描述:Counter, Up, 4 Bit Binary, 16 Pin, Ceramic, DIP |
| MC14520BCP | 功能描述:計數器移位寄存器 3-18V Dual BCD Up RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
| MC14520BCPG | 功能描述:計數器移位寄存器 3-18V Dual BCD Up RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。