參數資料
型號: MC12181D
廠商: MOTOROLA INC
元件分類: XO, clock
英文描述: 125 - 1000 MHZ FREQUENCY SYNTHESIZER
中文描述: PLL FREQUENCY SYNTHESIZER, 1000 MHz, PDSO16
封裝: PLASTIC, SO-16
文件頁數: 7/9頁
文件大小: 110K
代理商: MC12181D
MC12181
7
MOTOROLA RF/IF DEVICE DATA
Figure 8. Closed Loop Frequency Response for
ζ
= 1
Natural Frequency
–60
–50
–40
–30
–20
–10
0
10
0.1
1.0 k
Hz
d
1.0
10
100
3dB Bandwidth
To simplify analysis further a damping factor of 1 will be
selected. The normalized closed loop response is illustrated
in Figure 8 where the loop bandwidth is 2.5 times the loop
natural frequency (the loop natural frequency is the
frequency at which the loop would oscillate if it were
unstable). Therefore the optimum loop bandwidth is
15 kHz/2.5 or 6.0 kHz (37.7 krads) with a damping coefficient,
ζ
1. T(s) is the transfer function of the loop filter.
T(s)
RoCos
1
NCo
KpKv
s2
RoCos
1
2
o
s
1
1
o2
s2
2
o
s
1
NCo
KpKv
1
o2
o
KpKv
NCo
Co
KpKv
N o2
RoCo
2
o
oRoCo
2
Ro
2
oCo
where Nt = Total PLL Divide Ratio — 8
×
N where (N = 25...40)
Kv = VCO Gain — Hz/V
Kp = Phase Detector/Charge Pump Gain — A
= ( |IOH| + |IOL| ) / 2
Technically, Kv and Kp should be expressed in Radian
units [Kv (RAD/V), Kp (A/RAD)]. Since the component
design equation contains the Kv
×
Kp term. the 2
π
cancels and the values can be epressed as above.
Figure 9. Design Equations for the 2nd Order System
In summary, follow the steps given below:
Step 1: Plot the phase noise of crystal reference and the
VCO on the same graph.
Step 2: Increase the phase noise of the crystal reference by
the noise contribution of the loop.
Step 3: Convert the divide–by–N to dB (20log 8
×
N) and
increase the phase noise of the crystal reference by
that amount.
Step 4: The point at which the VCO phase noise crosses the
amplified phase noise of the Crystal Reference is the
point of the optimum loop bandwidth. This is
approximately 15 kHz in Figure 7.
Step 5: Correlate this loop bandwidth to the loop natural
frequency per Figure 8. In this case the 3.0 dB
bandwidth for a damping coefficient of 1 is 2.5 times
the loop’s natural frequency. The relationship
between the 3.0 dB loop bandwidth and the loop’s
“natural” frequency will vary for different values of
ζ
.
Making use of the equations defined in Figure 9, a
math tool or spread sheet is useful to select the
values for Ro and Co.
Appendix: Derivation of Loop Filter Transfer Function
The purpose of the loop filter is to convert the current from
the phase detector to a tuning voltage for the VCO. The total
transfer function is derived in two steps. Step 1 is to find the
voltage generated by the impedance of the loop filter. Step 2
is to find the transfer function from the input of the loop filter to
its output. The “voltage” times the “transfer function” is the
overall transfer function of the loop filter. To use these
equations in determining the overall transfer function of a PLL
multiply the filter’s impedance by the gain constant of the
phase detector then multiply that by the filter’s transfer
function (Figure 10 contains the transfer function equations
for 2nd, 3rd and 4th order PLL filters.)
相關PDF資料
PDF描述
MC12429 High Frequency PLL Clock Generator(高頻PLL時鐘發生器)
MC12430 High Frequency PLL Clock Generator(高頻PLL時鐘發生器)
MC13025 Electronically Tuned Radio Front End
MC13028A C-QUAM AM STEREO ADVANCED WIDE VOLTAGE IF and DECODER for E.T.R. RADIOS
MC13109 Universal Cordless Telephone Subsystem IC
相關代理商/技術參數
參數描述
MC1218F 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC1218L 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC-121EU 制造商:Amphenol Aerospace 功能描述:HEADSET CONNECTOR 制造商:Amphenol Nexus 功能描述:HEADSET CONNECTOR - Bulk
MC-121SP 制造商:Amphenol Nexus 功能描述:HEADSET CONNECTOR - Bulk
MC1220 功能描述:電源線濾波器 Filter 250V 20A RoHS:否 制造商:EPCOS 電壓額定值:277 VAC 電流額定值:100 A 安裝風格:Chassis 端接類型:Screw