- 您現在的位置：買賣IC網 > PDF目錄45202 > MB9BF505RPMC 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB9BF505RPMC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封裝： | 16 X 16 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-120 |
| 文件頁數： | 113/120頁 |
| 文件大小： | 1277K |
| 代理商： | MB9BF505RPMC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁當前第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
92
8266D-MCU Wireless-06/12
ATmega128RFA1
for transmission, the antenna must be set using the ANT_CTRL bits based on the value
read from the ANT_SEL bit. It is recommended to read bit ANT_SEL after the
TRX24_RX_START interrupt.
The autonomous search and selection allows the use of Antenna Diversity during
reception even if the application software currently does not control the radio
transceiver for instance in Extended Operating Mode.
An application software defined selection of a certain antenna can be done by disabling
the automatic Antenna Diversity algorithm (ANT_DIV_EN = 0) and selecting one
antenna using register bit ANT_CTRL.
If the radio transceiver is not in a receive or transmit state, it is recommended to disable
register bit ANT_EXT_SW_EN and to set the port pins DIG1 and DIG2 to output low via
the I/O port control register (DDG1 = 1, PORTG1 = 0, DDF2 = 1, PORTF2 = 0). In this
way the power consumption of the external RF switch is reduced and leakage currents
are avoided especially during sleep modes.
9.8.3.3 Antenna Diversity with Extended Operation Modes
A combination of Extended Operation Mode and antenna diversity is allowed.
While the radio transceiver is in RX_AACK_ON state, it switches to an antenna with a
reliable signal. The receive antenna selection is also used for transmission of an
automatic acknowledge frame.
While the radio transceiver is in TX_ARET state, the selected antenna is automatically
changed for every frame transmission retry.
9.8.3.4 Antenna Diversity Sensitivity Control
The detection threshold of the receiver has to be adjusted due to a different receive
algorithm used by the Antenna Diversity algorithm. It is recommended to set bits
PDT_THRES of register RX_CTRL to 3.
9.8.4 RX/TX Indicator
The main features are:
RX/TX Indicator to control an external RF Front-End;
Application software independent RF Front-End Control;
Provide TX Timing Information;
9.8.4.1 Overview
While IEEE 802.15.4 is a low-cost, low-power standard, solutions supporting higher
transmit output power are occasionally desirable. A differential control pin pair can
indicate that the radio transceiver is currently in transmit mode to simplify the control of
an optional external RF front-end.
The control of an external RF front-end is done via the digital control pins DIG3/DIG4.
The function of this pin pair is enabled with bit PA_EXT_EN of register TRX_CTRL_1.
Pin DIG3 is set to low level and DIG4 to high level while the transmitter is turned off.
The two pins change the polarity when the radio transceiver starts transmitting. This
differential pin pair can be used to control PA, LNA and RF switches. See also
If the radio transceiver is not in a receive or transmit state, it is recommended to disable
register bit PA_EXT_EN and to set the port pins DIG3 and DIG4 to output low via the
相關PDF資料 |
PDF描述 |
|---|---|
| MB9BF516TBGL | 32-BIT, FLASH, RISC MICROCONTROLLER, PBGA192 |
| MB9BF517TPMC | 32-BIT, FLASH, RISC MICROCONTROLLER, PQFP176 |
| MB9BF517SPMC | 32-BIT, FLASH, RISC MICROCONTROLLER, PQFP144 |
| MB9BF518TPMC | 32-BIT, FLASH, RISC MICROCONTROLLER, PQFP176 |
| MB9BF516SPMC | 32-BIT, FLASH, RISC MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB9BF506NABGL-GE1 | 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 112BGA 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 112BGA, Controller Family/Series:ARM Cortex-M3, Core |
| MB9BF506NAPMC-G-JNE1 | 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 32BIT CORTEX-M3 FM3 100LQFP 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 100LQFP 制造商:FUJITSU 功能描述:MCU, 32BIT, CORTEX-M3, FM3, 100LQFP, Controller Family/Series:ARM Cortex-M3, Core Size:32bit, No. of I/O's:80, Supply Voltage Min:2.7V, Supply Voltage Max:5.5V, Digital IC Case Style:LQFP, No. of Pins:100, Program Memory Size:512KB, , RoHS Compliant: Yes |
| MB9BF506NBBGL-GE1 | 制造商:FUJITSU 功能描述: |
| MB9BF506NBPMC-G-JNE2 | 制造商:FUJITSU 功能描述: |
| MB9BF506NPMC-ESE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。