- 您現在的位置：買賣IC網 > PDF目錄69021 > MB91121PFV 32-BIT, 50 MHz, RISC MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB91121PFV |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, 50 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封裝： | PLASTIC, LQFP-120 |
| 文件頁數： | 7/100頁 |
| 文件大小： | 2316K |
| 代理商： | MB91121PFV |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
MB91121 Series
14
DS07-16303-4E
■ HANDLING DEVICES
Preventing Latchup
In CMOS ICs, applying voltage higher than VCC or lower than VSS to input/output pin or applying voltage over
rating across VCC and VSS may cause latchup.
This phenomenon rapidly increases the power supply current, which may result in thermal breakdown of the
device. Make sure to prevent the voltage from exceeding the maximum rating.
Take care that the analog power supply (AVCC AVR) and the analog input do not exceed the digital power supply
(VCC) when the analog power supply turned on or off.
Treatment of Unused Pins
Unused pins left open may cause malfunctions. Make sure to connect them to pull-up or pull-down resistors.
External Reset Input
It takes at least 5 machine cycle to input “L” level to the RST pin and to ensure inner reset operation properly.
Remarks for External Clock Operation
When external clock is selected, supply it to X0 pin generally, and simultaneously the opposite phase clock to
X0 must be supplied to X1 pin. However, in this case the stop mode must not be used (because X1 pin stops
at “H” output in stop mode) .
And can be used to supply only to X0 pin with 5 V power supply at 12.5 MHz and less than.
Power Supply Pins
When there are several VCC and VSS pins, each of them is equipotentially connected to its counterpart inside of
the device, minimizing the risk of malfunctions such as latch up. To further reduce the risk of malfunctions, to
prevent EMI radiation, to prevent strobe signal malfunction resulting from creeping-up of ground level and to
observe the total output current standard, connect all VCC and VSS pins to the power supply or GND.
It is preferred to connect VCC and VSS of MB91121 to power supply with minimal impedance possible.
It is also recommended to connect a ceramic capacitor as a bypass capacitor of about 0.1
F between VCC and
VSS at a position as close as possible to MB91121.
X0
X1
OPEN
MB91121 series
X0
X1
MB91121 series
Using an external clock (normal)
Note: Can not be used stop mode (oscillation stop mode).
Using an external clock (can be used at 12.5 MHz and less than.)
Using an external clock
相關PDF資料 |
PDF描述 |
|---|---|
| MB91154PFV-G-XXX | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91F155APFV-G | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91233LLGA-G-xxx-BNDE1 | 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91233LPMC1-G-XXXE1 | 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F233APMC1-GE1 | 32-BIT, FLASH, 33.6 MHz, RISC MICROCONTROLLER, PQFP120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91133 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit RISC Microcontroller |
| MB91133PBT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit RISC Microcontroller |
| MB91133PMT2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit RISC Microcontroller |
| MB91150 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
| MB91151A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。