- 您現在的位置：買賣IC網 > PDF目錄69021 > MB90F474LPF 16-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MB90F474LPF |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 28/118頁 |
| 文件大?。?/td> | 1199K |
| 代理商： | MB90F474LPF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁
MB90470 Series
17
(6) Precautions for use of external oscillators (crystals)
The target value for the upper limit of oscillator (crystals) frequencies should be 20 MHz. Also, when operating
at internal frequencies of 16 MHz, the PLL multiplier should be used.
(7) Proper power-on/off sequence
The A/D converter power (AVCC, AVRH) and analog input (AN0 to AN7) must be turned on after the digital power
supply (VCC) is turned on. The A/D converter power (AVCC, AVRH) and analog input (AN0 to AN7) must be shut
off before the digital power supply (VCC) is shut off. Care should be taken that AVRH does not exceed AVCC. Even
when pins used as analog input pins are doubled as input ports, be sure that the input voltage does not exceed
AVCC.
Note : VCC
= VCC3 = VCC5
(8) Treatment of A/D converter power supply pins
Even if the A/D converter is not used, pins should be connected so that AVCC
= AVRH = VCC, and AVSS = VSS.
(9) Power-on procedures
In order to prevent abnormal operation of the internal built-in step-down circuits, voltage rise during power-on
should be attained within 50
s (0.2 V to 2.7 V) .
(10) Stable power supply
Even within the operating range of the VCC supply voltage, rapid changes in supply voltage may cause abnormal
operation. As a basis for stable operation, it is recommended that voltage variation be restricted in order to limit
VCC ripple fluctuations (P-P values) to 10
% at commercial frequencies of 50 Hz to 60 Hz, and transient fluctuations
to 0.1 V/ms at instantaneous points such as power switching.
(11) Precautions for use of two power supplies
The MB90470 series usually uses the 3-V power supply as the main power source. With VCC3
= 3 V and
VCC5
= 5 V, however, it can interface with P20/A16 to P27/A23/PPG3, P30/A00/AIN0 to P37/A07/PWC1,
P40/A08/SIN2 to P47/A15/OUT5, P70/SIN0 to P77/SDA for the 5-V power supply separetely from the 3-V power
supply at all operation mode.
(Caution) The analog power supply for the A/D converter (AVCC, AVSS etc.) can only operate with the
3 V system.
(12) Crystal oscillator circuits during power-saving operation
When the power supply is lower than 2.0 V, the external crystal oscillator may not operate even when power is
on. For this reason, the use of an external clock signal is recommended.
(13) Caution : low-voltage flash models (2.4 V to 3.6 V/10 MHz) do not have security functions
(14) Treatment of unused input pins
N.C. (internally connected) pins should always be left open.
(15) When the dual-supply MB90470 series is used as a 1-supply device, use connections so that
X0A
==== VSS, and X1A ==== Open.
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F483PFV | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100 |
| MB90F523BPFV | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP120 |
| MB90522APFF | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP120 |
| MB90523APFF | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP120 |
| MB90522BPFV | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F474LPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F474LPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F482PFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F482PFR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F482PMC-G-JNE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。