參數資料
型號： MB90F394HAPMT
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 16-bit Proprietary Microcontroller
中文描述： 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120
封裝： 16 X 16 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-120
文件頁數： 44/71頁
文件大?。?/td> 445K
代理商： MB90F394HAPMT
MB90390 Series
44
(Continued)
*1 : The parameter is based on V
SS
=
AV
SS
=
DV
SS
=
0.0 V.
*2 : Set AV
CC
and V
CC
to the same voltage. Make sure that AV
CC
does not exceed V
CC
and that the voltage at the
analog inputs does not exceed AV
CC
when the power is switched on.
*3 : V
I
and V
O
should not exceed V
CC
+
0.3 V. V
I
should not exceed the specified ratings. However if the maximum
current to/from a input is limited by some means with external components, the I
CLAMP
rating supersedes the
V
I
rating. For ports P70 to P77, P80 to P87 and PA0 to PA7, V
I
and V
O
should not exceed DV
CC
+
0.3 V.
*4 : Applicable to pins : P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67,
P90 to P97, PB0 to PB7
*5 : Applicable to pins : P70 to P77, P80 to P87, PA0 to PA7
*6 :
Applicable to pins : P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67
P70 to P77, P80 to P87, P90 to P97, PA0 to PA7, PB0 to PB7
Use within recommended operating conditions.
Use at DC voltage (current)
The
+
B signal should always be applied a limiting resistance placed between the
+
B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the
+
B signal is applied the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the
+
B input
potential may pass through the protective diode and increase the potential at the V
CC
pin, and this may affect
other devices.
Note that if a
+
B signal is input when the microcontroller power supply is off (not fixed at 0 V) , the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the
+
B input is applied during power-on, the power supply is provided from the pins and the
resulting supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the
+
B input pin open.
Note that analog system input/output pins other than the A/D input pins (LCD drive pins, comparator input
pins, etc.) cannot accept
+
B signal input.
Sample recommended circuits:
WARNING:
Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
Pch
Nch
V
CC
R
Input/output equivalent circuits
+
B input (0 V to 16 V)
Limiting
resistance
Protective diode
相關PDF資料
PDF描述
MB90F394H 16-bit Proprietary Microcontroller CMOS
MB90F394HPMT 16-bit Proprietary Microcontroller CMOS
MB90F444G 16-bit Proprietary Microcontroller
MB90443G 16-bit Proprietary Microcontroller
MB90443GPF 16-bit Proprietary Microcontroller
相關代理商/技術參數
參數描述
MB90F394HPMCR-GE1 制造商:FUJITSU 功能描述:
MB90F395HAPMCR-GS-SPE 制造商:FUJITSU 功能描述:16-BIT, FLASH, 24 MHZ, MICROCONTROLLER, PQFP120
MB90F428GAPMC-GSE1 制造商:FUJITSU 功能描述:
MB90F428GCPFR-GSE1 制造商:FUJITSU 功能描述:
MB90F438LSPFR-GE1 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*