參數資料
型號： MB90F394HAPMT
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 16-bit Proprietary Microcontroller
中文描述： 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120
封裝： 16 X 16 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-120
文件頁數： 16/71頁
文件大?。?/td> 445K
代理商： MB90F394HAPMT
MB90390 Series
16
■
HANDLING DEVICES
Special care is required for the following when handling the device :
Preventing latch-up
Stabilization of supply voltage
Treatment of unused pins
Using external clock
Power supply pins (V
CC
/V
SS
)
Pull-up/down resistors
Crystal Oscillator Circuit
Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Connection of Unused Pins of A/D Converter if A/D Converter is unused.
Notes on Energization
Caution on Operations during PLL Clock Mode
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions :
A voltage higher than V
CC
or lower than V
SS
is applied to an input or output pin.
A voltage higher than the rated voltage is applied between V
CC
and V
SS
pins.
The AV
CC
power supply is applied before the V
CC
voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AV
CC
, AVRH) exceed the digital
power-supply voltage.
Stabilization of supply voltage
2.
A sudden change in the supply voltage may cause the device to malfunction even within the specified V
CC
supply
voltage operating range. Therefore, the V
CC
supply voltage should be stabilized.
For reference, the supply voltage should be controlled so that V
CC
ripple variations (peak-to-peak values) at
commercial frequencies (50/60 Hz) fall below 10% of the standard V
CC
supply voltage and the coefficient of
fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
Treatment of unused pins
3.
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should
be more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
Using external clock
4.
To use external clock, drive the X0 pin and leave X1 pin open.
X0
X1
MB90390 Series
相關PDF資料
PDF描述
MB90F394H 16-bit Proprietary Microcontroller CMOS
MB90F394HPMT 16-bit Proprietary Microcontroller CMOS
MB90F444G 16-bit Proprietary Microcontroller
MB90443G 16-bit Proprietary Microcontroller
MB90443GPF 16-bit Proprietary Microcontroller
相關代理商/技術參數
參數描述
MB90F394HPMCR-GE1 制造商:FUJITSU 功能描述:
MB90F395HAPMCR-GS-SPE 制造商:FUJITSU 功能描述:16-BIT, FLASH, 24 MHZ, MICROCONTROLLER, PQFP120
MB90F428GAPMC-GSE1 制造商:FUJITSU 功能描述:
MB90F428GCPFR-GSE1 制造商:FUJITSU 功能描述:
MB90F438LSPFR-GE1 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*