- 您現在的位置：買賣IC網 > PDF目錄69020 > MB90F334APMC1 (FUJITSU LTD) 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB90F334APMC1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120 |
| 封裝： | 14 X 14 MM, 1.70 MM HEIGHT, 0.40 MM PITCH, PLASTIC, LFQFP-120 |
| 文件頁數： | 8/72頁 |
| 文件大小： | 1857K |
| 代理商： | MB90F334APMC1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MB90330A Series
16
DS07-13734-9E
6.
About Crystal oscillator circuit
Noise near the X0/X1 pins and X0A/X1A pins may cause the device to malfunction. Design the printed circuit
board so that X0/X1 pins and X0A/X1A pins, the crystal oscillator (or the ceramic oscillator) and the bypass
capacitor to ground are located as close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0/X1 pins and X0A/X1A pins surrounded
by ground plane because stable operation can be expected with such a layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
7.
Caution on Operations during PLL Clock Mode
On this microcontroller, if in case the crystal oscillator breaks off or an external reference clock input stops while
the PLL clock mode is selected, a self-oscillator circuit contained in the PLL may continue its operation at its
self-running frequency. However, Fujitsu will not guarantee results of operations if such failure occurs.
8.
Stabilization of supply voltage
A sudden change in the supply voltage may cause the device to malfunction even within the VCC supply voltage
operating range. For stabilization reference, the supply voltage should be stabilized so that VCC ripple variations
(peak-to-peak value) at commercial frequencies (50 Hz/60 Hz) fall below 10
% of the standard VCC supply voltage
and the transient regulation does not exceed 0.1 V/ms at temporary changes such as power supply switching.
9.
When the dual-supply is used as a single-supply device
If you are using only a single-system of the MB90330A series that come in the dual-system product, use it with
X0A
= VSS : X1A = OPEN.
10. Writing to flash memory
For serial writing to flash memory, always make sure that the operating voltage VCC is between 3.13 V and 3.6 V.
For normal writing to flash memory, always make sure that the operating voltage VCC is between 3.0 V and 3.6 V.
11. Serial communication
There is a possibility to receive wrong data due to noise or other causes on the serial communication. Therefore,
design a printed circuit board so as to avoid noise.
Consider receiving of wrong data when designing the system. For example, apply a checksum to detect an error.
If an error is detected, retransmit the data.
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F395HAPMT | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120 |
| MB90F428GBPFV | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90F423GBPFV | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90423GBPFV | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90427GBPFV | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F334APMC1-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC1-G-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-SNE1 | 制造商:FUJITSU 功能描述: |
| MB90F334APMC-G-SPE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。