- 您現在的位置：買賣IC網 > PDF目錄45186 > MB89PV630C-SH 8-BIT, 10 MHz, MICROCONTROLLER, CDIP64 PDF資料下載
參數資料
| 型號： | MB89PV630C-SH |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, 10 MHz, MICROCONTROLLER, CDIP64 |
| 封裝： | CERAMIC, MDIP-64 |
| 文件頁數： | 104/153頁 |
| 文件大?。?/td> | 7326K |
| 代理商： | MB89PV630C-SH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁當前第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁
HARDWARE CONFIGURATION
2-31
P30 to P37 CMOS-type I/O ports (also used as resource input/output)
Switching input and output
This port has a data-direction register (DDR) and a port-data register (PDR) for each bit. Input and out-
put can be set independently for each bit. The pin with the DDR set to 1 is set to output, and the pin with
the DDR set to 0 is set to input. When the resource-output enable bit is enabled, the pin is set to output
irre spective of the DDR setting conditions.
Operation for output port (DDR = 1)
The value written at the PDR is output to the pin when the DDR is set to 1. When the PDR is read, usu-
ally, the value of the pin is read instead of the contents of the output latch. However, when the Read
Modify Write instruction is executed, the contents of the output latch are read irrespective of the DDR
setting con ditions. Therefore, the bit-processing instruction can be used even if input and output are
mixed with each other. When data is written to the PDR, the written data is held in the output latch irre-
spective of the DDR setting conditions.
P33 to P35 can be selected from either CMOS (Bit X = 0) or N-ch open drain (Bit X = 1).
Operation for input port (DDR = 0)
When used as the input port, the output impedance goes High. Therefore, when the PDR is read, the
value of the pin is read.
Operation for resource output
When using as the resource output, setting is performed by the resource output- enable bit. (See the de
scription of each resource.) If the output of each resource is enabled with the DDR set to 0, the port is
set to output. Since the reading of the parallel port is effective even if the output of each resource is
enabled, the output value of each resource can be read.
Operation for resource input
Input to the resource is irrelevant to the setting conditions of the DDR and resource. The value of the pin
is always input to the port serving as the resource input. When using an external signal at the resource,
set the DDR to input.
State when reset
When reset, the DDR and resource output-enable bit are initialized to 0 and the output impedance goes
High at all bits. (Pins with activated pull-up resistors are in the pull-up state.) When reset, the PDR is
unde fined. Therefore, set the value of the PDR before setting the DDR to output.
State in stop mode
With the SPL bit of the standby-control register set to 1, in the stop mode, the output impedance goes
High irrespective of the value of the DDR. (Pins with activated pull-up resistors are in the pull-up state.)
相關PDF資料 |
PDF描述 |
|---|---|
| MB89P637-SH | 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PDIP64 |
| MB89636RP-SH | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP64 |
| MB89635RP-SH | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP64 |
| MB89635RPF | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP64 |
| MB89PV950CF | 8-BIT, 5 MHz, MICROCONTROLLER, CQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB89PV640CF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89PV650A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89PV650ACF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89PV670A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89PV670ACF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。