![](http://datasheet.mmic.net.cn/330000/MB814405D-60_datasheet_16435856/MB814405D-60_10.png)
10
MB814405D-60/60L/-70/70L
Notes:
*1.
Referenced to V
SS
.
I
CC
depends on the output load conditions and cycle rates; The specified values are obtained with the
output open.
I
CC
depends on the number of address change as RAS = V
IL
and CAS = V
IH
I
CC1
, I
CC3
and I
CC5
are specified at one time of address change during RAS = V
IL
and CAS = V
IH
.
I
CC4
is specified at one time of address change during one Page cycle.
An Initial pause (RAS = CAS = V
IH
) of 200
μ
s is required after power-up followed by any eight RAS-
only cycles before proper device operation is achieved. In case of using internal refresh counter, a
minimum of eight CAS-before-RAS initialization cycles instead of 8 RAS cycles are required.
AC characteristics assume t
T
= 2 ns.
V
IH
(min) and V
IL
(max) are reference levels for measuring timing of input signals. Also transition times
are measured between V
IH
(min) and V
IL
(max).
Assumes that t
RCD
≤
t
RCD
(max), t
RAD
≤
t
RAD
(max). If t
RCD
is greater than the maximum recommended
value shown in this table, t
RAC
will be increased by the amount that t
RCD
exceeds the value shown. Refer
to Fig. 2 and 3.
If t
RCD
≥
t
RCD
(max), t
RAD
≥
t
RAD
(max), and t
ASC
≥
t
AA
- t
CAC
- t
T
, access time is t
CAC
.
If t
RAD
≥
t
RAD
(max) and t
ASC
≤
t
AA
- t
CAC
- t
T
, access time is t
AA
.
Measured with a load equivalent to two TTL loads and 100 pF.
t
OFF
, t
OFR
, t
WEZ
and t
OEZ
is specified that output buffer change to high impedance state.
Operation within the t
RCD
(max) limit ensures that t
RAC
(max) can be met. t
RCD
(max) is specified as a
reference point only; if t
RCD
is greater than the specified t
RCD
(max) limit, access time is controlled
exclusively by t
CAC
or t
AA
.
t
RCD
(min) = t
RAH
(min) + 2t
T
+ t
ASC
(min).
Operation within the t
RAD
(max) limit ensures that t
RAC
(max) can be met. t
RAD
(max) is specified as a
reference point only; if t
RAD
is greater than the specified t
RAD
(max) limit, access time is controlled
exclusively by t
CAC
or t
AA
.
Either t
RRH
or t
RCH
must be satisfied for a read cycle.
t
WCS
is specified as a reference point only. If t
WCS
≥
t
WCS
(min) the data output pin will remain High-Z
state through entire cycle.
Assumes that t
WCS
< t
WCS
(min).
Either t
DZC
or t
DZO
must be satisfied.
t
CPA
is access time from the selection of a new column address (that is caused by changing CAS from
“L” to “H”). Therefore, if t
CP
is long, t
CPA
is longer than t
CPA
(max) as shown in Fig. 4.
Assumes that CAS-before-RAS refresh.
Assumes that Test mode function.
The last CAS rising edge.
The first CAS falling edge.
*2.
*3.
*4.
*5.
*6.
*7.
*8.
*9.
*10.
*11.
*12.
*13.
*14.
*15.
*16.
*17.
*18.
*19.
*20.
*21.
*22.