- 您現在的位置：買賣IC網 > PDF目錄2092 > MAX9796EBX+TG45 (Maxim Integrated Products)IC AMP AUDIO 2.3W MONO D 36UCSP PDF資料下載
參數資料
| 型號： | MAX9796EBX+TG45 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 18/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO 2.3W MONO D 36UCSP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | DirectDrive® |
| 類型： | D 類 |
| 輸出類型： | 1-通道（單聲道），帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 2.3W x 1 @ 4 歐姆 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，I²C，靜音，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 36-UCSP |
| 封裝/外殼： | 36-WFBGA，CSBGA |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Single-Ended Input
The MAX9796 can be configured as a single-ended
input amplifier by appropriately configuring the Input
Control Register (see Tables 5a and 5b).
DC-Coupled Input
The input amplifier can accept DC-coupled inputs that
are biased to the amplifier’s bias voltage. DC-coupling
eliminates the input-coupling capacitors; reducing com-
ponent count to potentially six external components (see
the
Typical Application Circuit). However, the highpass
filtering effect of the capacitors is lost, allowing low-fre-
quency signals to feed through to the load.
Unused Inputs
Connect any unused input directly to VBIAS. This saves
input capacitors on unused inputs and provides the
highest noise immunity on the input.
Component Selection
Input Filter
An input capacitor (CIN) in conjunction with the input
impedance of the MAX9796 forms a highpass filter that
removes the DC bias from the incoming signal. The AC-
coupling capacitor allows the amplifier to automatically
bias the signal to an optimum DC level. Assuming zero
source impedance, the -3dB point of the highpass filter
is given by:
Choose CIN so that f-3dB is well below the lowest fre-
quency of interest. Use capacitors whose dielectrics
have low-voltage coefficients, such as tantalum or alu-
minum electrolytic. Capacitors with high-voltage coeffi-
cients, such as ceramics, may result in increased
distortion at low frequencies.
Other considerations when designing the input filter
include the constraints of the overall system and the
actual frequency band of interest. Although high-fidelity
audio calls for a flat-gain response between 20Hz and
20kHz, portable voice-reproduction devices, such as
cell phones and two-way radios, need only concentrate
on the frequency range of the spoken human voice
(typically 300Hz to 3.5kHz). In addition, speakers used
in portable devices typically have a poor response
below 300Hz. Taking these two factors into considera-
tion, the input filter may not need to be designed for a
20Hz to 20kHz response, saving both board space and
cost due to the use of smaller capacitors.
Class D Output Filter
The MAX9796 does not require a Class D output filter.
The device passes EN55022B emissions standards
with 152mm of unshielded speaker cables. However,
output filtering can be used if a design is failing radiat-
ed emissions due to board layout or cable length, or
the circuit is near EMI-sensitive devices. Use a ferrite
bead filter when radiated frequencies above 10MHz
are of concern. Use an LC filter when radiated frequen-
cies below 10MHz are of concern, or when long leads
(>152mm) connect the amplifier to the speaker. Figure
11 shows optional speaker amplifier output filters.
External Component Selection
BIAS Capacitor
VBIAS is the output of the internally generated DC bias
voltage. The VBIAS bypass capacitor, CVBIAS improves
PSRR and THD+N by reducing power supply and other
noise sources at the common-mode bias node, and
also generates the clickless/popless, startup/shutdown
DC bias waveforms for the speaker amplifiers. Bypass
VBIAS with a 1F capacitor to GND.
f
RC
dB
IN IN
=
3
1
2
π
MAX9796
2.3W, High-Power Class D Audio Subsystem
with DirectDrive Headphone Amplifiers
______________________________________________________________________________________
25
OUT_+
OUT_-
33
μH
33
μH
0.47
μF
0.033
μF
0.1
μF
22
Ω
22
Ω
0.033
μF
0.1
μF
Figure 11. Speaker Amplifier Output Filter
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9813LEKA+T | IC AMP AUDIO MONO AB MIC SOT23-8 |
| MAX9814ETD+T | IC AMP AUDIO MONO AB MIC 14TDFN |
| MAX9820ETB+T | IC AMP AUD HDPHE 95MW 10TDFN |
| MAX98300SETA+T | IC AMP AUD SPKR 2W MONO D 8TDFN |
| MAX98302ETD+ | IC AMP STER CLASS D 2.4W 14TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9796EVKIT | 制造商:Maxim Integrated Products 功能描述:2.3W HIGH-POWER CLASS D AUDIO SUBS - Rail/Tube |
| MAX9796EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX9796 EVAL KIT - Boxed Product (Development Kits) |
| MAX98088EVKIT# | 功能描述:音頻 IC 開發工具 MAX98088 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX98088EVKIT+ | 功能描述:音頻 IC 開發工具 MAX98088 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX98088EWY+T | 功能描述:接口—CODEC Dual I2S Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。