- 您現在的位置：買賣IC網 > PDF目錄11329 > MAX9598CTL+ (Maxim Integrated Products)IC SWITCH DUAL SCART 40TQFN PDF資料下載
參數資料
| 型號： | MAX9598CTL+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/36頁 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DUAL SCART 40TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 功能： | 開關 |
| 電路： | 2 x SCART |
| 導通狀態電阻： | 7 歐姆 |
| 電壓電源： | 單/雙電源 |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 3.6 V，±11.4 V ~ 12.6 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-TQFN-EP（6x6） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
MAX9598
START and STOP Conditions
SDA and SCL idle high when the bus is not in use. A
master initiates communication by issuing a START con-
dition. A START condition is a high-to-low transition on
SDA with SCL high. A STOP condition is a low-to-high
transition on SDA while SCL is high (Figure 7). A START
condition from the master signals the beginning of a
transmission to the MAX9598. The master terminates
transmission, and frees the bus, by issuing a STOP con-
dition. The bus remains active if a REPEATED START
condition is generated instead of a STOP condition.
Early STOP Conditions
The MAX9598 recognizes a STOP condition at any
point during data transmission except if the STOP con-
dition occurs in the same high pulse as a START condi-
tion. For proper operation, do not send a STOP
condition during the same SCL high pulse as the
START condition.
Slave Address
The slave address is defined as the 7 MSBs (most sig-
nificant bits) followed by the R/W(read/write) bit. Set
the R/W bit to 1 to configure the MAX9598 to read
mode. Set the R/W bit to 0 to configure the MAX9598 to
write mode. The slave address is always the first byte
of information sent to the MAX9598 after a START or a
REPEATED START condition. The MAX9598 slave
address is configurable with DEV_ADDR. Table 3
shows the possible slave addresses for the MAX9598.
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
MAX9598 uses to handshake receipt of each byte of
data when in write mode (see Figure 8). The MAX9598
pulls down SDA during the entire master-generated 9th
clock pulse if the previous byte is successfully received.
Monitoring ACK allows for detection of unsuccessful data
transfers. An unsuccessful data transfer occurs if a
receiving device is busy or if a system fault has
occurred. In the event of an unsuccessful data transfer,
the bus master may retry communication. The master
pulls down SDA during the 9th clock cycle to acknowl-
edge receipt of data when the MAX9598 is in read mode.
An acknowledge is sent by the master after each read
byte to allow data transfer to continue. A not acknowl-
edge is sent when the master reads the final byte of data
from the MAX9598, followed by a STOP condition.
Low-Power Audio/Video Switch for
Dual SCART Connectors
18
______________________________________________________________________________________
SCL
SDA
SSr
P
Figure 7. START, STOP, and REPEATED START Conditions
1
SCL
START
CONDITION
SDA
28
9
CLOCK PULSE FOR
ACKNOWLEDGMENT
ACKNOWLEDGE
NOT ACKNOWLEDGE
Figure 8. Acknowledge
Table 3. Slave Address
DEV_ADDR
B7
B6
B5
B4
B3
B2
B1
B0
WRITE ADDRESS
(hex)
READ ADDRESS
(hex)
GNDVID
1
0
01010
R/W
94h
95h
VVID
1
0
01011
R/W
96h
97h
SCL
10
01100
R/W
98h
99h
SDA
10
01101
R/W
9Ah
9Bh
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2WB-IX-F1 | CONVERTER MOD DC/DC 95V 75W |
| DSPIC33FJ32GS406-I/MR | IC MCU/DSP 32KB FLASH 64QFN |
| VI-220-IX-F2 | CONVERTER MOD DC/DC 5V 75W |
| MAX4051CEE+ | IC MULTIPLEXER 8X1 16QSOP |
| VI-220-IX-F1 | CONVERTER MOD DC/DC 5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9598CTL+ | 功能描述:視頻開關 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX9598CTL+T | 功能描述:視頻開關 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX9598EVKIT+ | 功能描述:交換機 IC 開發工具 MAX9598 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| MAX9600EUP | 功能描述:校驗器 IC Dual ECL-D/Q PECL 500ps Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9600EUP+ | 功能描述:校驗器 IC Dual ECL-D/Q PECL 500ps Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。