- 您現在的位置：買賣IC網 > PDF目錄10821 > MAX5888EGK+TD (Maxim Integrated Products)IC DAC 16BIT 3.3V 500MSPS 68-QFN PDF資料下載
參數資料
| 型號： | MAX5888EGK+TD |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT 3.3V 500MSPS 68-QFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 設置時間： | 11ns |
| 位數： | 16 |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 130mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 68-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 68-QFN 裸露焊盤（10x10） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 2 電流，單極 |
| 采樣率（每秒）： | 500M |
MAX5888
3.3V, 16-Bit, 500Msps High Dynamic
Performance DAC with Differential LVDS Inputs
12
______________________________________________________________________________________
amplitudes. It is also recommended to center tap the
transformer to ground. If no transformer is used, each
DAC output should be terminated to ground with a 50
resistor. Additionally, a 100
resistor should be placed
between the outputs (Figure 8).
If a single-ended unipolar output is desirable, IOUTP
should be selected as the output, with IOUTN ground-
ed. However, driving the MAX5888 single ended is not
recommended since additional noise is added (from
the ground plane) in such configurations.
The distortion performance of the DAC depends on the
load impedance. The MAX5888 is optimized for a 50
double termination. It can be used with a transformer
output as shown in Figure 7 or just one 50
resistor
from each output to ground and one 50
resistor
between the outputs. This produces a full-scale output
power of up to 0dBm depending on the output current
setting. Higher termination impedance can be used at
the cost of degraded distortion performance and
increased output noise voltage.
Adjacent Channel Leakage Power Ratio
(ACLR) Testing for CDMA- and
WCDMA-Based Base Station
Transceiver Systems (BTS)
The transmitter sections of BTS applications serving
CDMA and WCDMA architectures must generate carri-
ers with minimal coupling of carrier energy into the adja-
cent channels. Similar to the GSM/EDGE model (see the
Multitone Testing for GSM/EDGE Applications section in
the Applications section), a transmit mask (Tx mask)
exists for this application. The spread-spectrum modula-
tion function applied to the carrier frequency generates a
spectral response, which is uniform over a given band-
width (up to 4MHz) for a WCDMA-modulated carrier.
A dominant specification is ACLR, a parameter which
reflects the ratio of the power in the desired carrier
band to the power in an adjacent carrier band. The
specification covers the first two adjacent bands, and is
measured on both sides of the desired carrier.
According to the transmit mask for CDMA and WCDMA
architectures, the power ratio of the integrated carrier
channel energy to the integrated adjacent channel
energy must be >45dB for the first adjacent carrier slot
(ACLR 1) and >50dB for the second adjacent carrier
slot (ACLR 2). This specification applies to the output of
the entire transmitter signal chain. The requirement for
only the DAC block of the transmitter must be tighter,
with a typical margin of >15dB, requiring the DAC’s
ACLR 1 to be better than 60dB. Adjacent channel leak-
age is caused by a single-spread spectrum carrier,
which generates intermodulation (IM) products
between the frequency components located within the
carrier band. The energy at one end of the carrier band
generates IM products with the energy from the oppo-
site end of the carrier band. For single-carrier WCDMA
modulation, these IMD products are spread 3.84MHz
over the adjacent sideband. Four contiguous WCDMA
MAX5888
T2, 1:1
T1, 1:1
VOUT, SINGLE ENDED
WIDEBAND RF TRANSFORMER T2
PERFORMS THE DIFFERENTIAL TO
SINGLE-ENDED CONVERSION.
50
100
50
IOUTP
IOUTN
B0–B15
16
AVDD
DVDD
VCLK
AGND
DGND
CLKGND
Figure 7. Differential to Single-Ended Conversion Using a Wideband RF Transformer
MAX5888
50
100
50
IOUTP
IOUTN
B0–B15
16
AVDD
DVDD
VCLK
AGND
DGND
CLKGND
OUTP
OUTN
Figure 8. MAX5888 Differential Output Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| MCP6541UT-E/OT | IC COMP PSH-PLL 1.6V SGL SOT23-5 |
| JKXER1G08FSSDSR | CONN RCPT 8POS PANEL MT SOLDER |
| MX7228KEWG+T | IC DAC 8BIT OCTAL 24-SOIC |
| MAX525BEPP+ | IC DAC 12BIT QUAD LP 20-DIP |
| MCP6546UT-E/OT | IC COMP O-D 1.6V SNGL SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5888EVKIT | 功能描述:數模轉換器- DAC Evaluation Kit for the MAX5886 MAX5887 MAX5888 RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5889EGK+D | 功能描述:數模轉換器- DAC 12-Bit 600Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5889EGK+TD | 功能描述:數模轉換器- DAC 12-Bit 600Msps DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5889EGK-D | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5889EGK-TD | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。