參數資料
型號： MAX1459AAP+T
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 模擬信號調理
英文描述： 2-Wire, 4-20mA Smart Signal Conditioner
中文描述： SPECIALTY ANALOG CIRCUIT, PDSO20
封裝： 5.30 MM, 0.65 MM PITCH, SSOP-20
文件頁數： 21/24頁
文件大小： 243K
代理商： MAX1459AAP+T
MAX1459
_______________Detailed Description
The MAX1459 provides an analog amplification path for
the sensor signal and a digital path for calibration and
temperature correction. Calibration and correction is
achieved by varying the offset and gain of a program-
mable-gain amplifier (PGA) and by varying the sensor
bridge current. The PGA utilizes a switched-capacitor
CMOS technology, with an input-referred offset trim-
ming range of ±63mV (9mV steps). An additional out-
put-referred fine offset trim is provided by the offset
DAC (approximately 2.8mV steps). The PGA provides
eight gain values from +41V/V to +230V/V. The bridge
current source is programmable from 0.1mA to 2mA.
The MAX1459 uses four 12-bit DACs with calibration
coefficients stored by the user in an internal 128-bit
EEPROM. This memory contains the following informa-
tion as 12-bit-wide words:
Configuration register
Offset calibration coefficient
Offset temperature error compensation coefficient
Full-span output (FSO) calibration coefficient
FSO temperature error compensation coefficient
24 user-defined bits for customer programming of
manufacturing data (e.g., serial number and date)
Figure 1 shows a typical pressure-sensor output and
defines the offset, full-scale, and FSO values as a func-
tion of voltage.
FSOTC Compensation
Silicon piezoresistive transducers (PRTs) exhibit a large
positive input resistance tempco (TCR) so that, while
under constant current excitation, the bridge voltage
(VBDRIVE) increases with temperature. This depen-
dence of VBDRIVE on the sensor temperature can be
used to compensate the sensor temperature errors.
PRTs also have a large negative full-span output sensi-
tivity tempco (TCS) so that, with constant voltage exci-
tation, FSO will decrease with temperature, causing a
full-span output temperature coefficient (FSOTC) error.
However, if the bridge voltage can be made to increase
with temperature at the same rate that TCS decreases
with temperature, the FSO will remain constant.
FSOTC compensation is accomplished by resistor
RFTC and the FSOTC DAC, which modulate the excita-
tion reference current at ISRC as a function of tempera-
ture (Figure 2). FSO DAC sets VISRC and remains
constant with temperature while the voltage at FSOTC
varies with temperature. FSOTC is the buffered output
of the FSOTC DAC. The reference DAC voltage is
VBDRIVE, which is temperature dependent. The FSOTC
DAC alters the tempco of the current source. When the
tempco of the bridge voltage is equal in magnitude and
opposite in polarity to the TCS, the FSOTC errors are
compensated and FSO will be constant with tempera-
ture.
OFFSET TC Compensation
Compensating offset TC errors involves first measuring
the uncompensated offset TC error, then determining
what percentage of the temperature-dependent voltage
VBDRIVE must be added to the output summing junction
to correct the error. Use the offset TC DAC to adjust the
amount of BDRIVE voltage that is added to the output
summing junction (Figure 3).
Analog Signal Path
The fully differential analog signal path consists of four
stages:
Front-end summing junction for coarse offset correction
3-bit PGA with eight selectable gains ranging from
41 through 230
Three-input-channel summing junction
Differential to single-ended output buffer with rail-to-
rail output (Figure 3)
Coarse Offset Correction
The sensor output is first fed into a differential summing
junction (INM (negative input) and INP (positive input))
with a CMRR > 90dB, an input impedance of approxi-
mately 1M
, and a common-mode input voltage range
from VSS to VDD. At this summing junction, a coarse off-
set-correction voltage is added, and the resultant volt-
2-Wire, 4–20mA
Smart Signal Conditioner
6
_______________________________________________________________________________________
VOLTAGE
(V)
PRESSURE
PMIN
PMAX
FULL-SCALE (FS)
4.5
0.5
FULL-SPAN OUTPUT (FSO)
OFFSET
Figure 1. Typical Pressure-Sensor Output
相關PDF資料
PDF描述
MAX1459CAP+ 2-Wire, 4-20mA Smart Signal Conditioner
MAX1459AAP+ 2-Wire, 4-20mA Smart Signal Conditioner
MAX147BEAP+ +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs
MAX147BEAP+T +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs
MAX147BCPP+ +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs
相關代理商/技術參數
參數描述
MAX1459CAP+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX1459CAP+T 制造商:Maxim Integrated Products 功能描述:SMART SGNL CONDITIONER 20SSOP - Tape and Reel
MAX1459CAP-T 制造商:Maxim Integrated Products 功能描述:#EMPTY - Tape and Reel
MAX145ACPA 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX145ACPA+ 功能描述:模數轉換器 - ADC 12-Bit 108ksps 5.25V High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*