- 您現在的位置：買賣IC網 > PDF目錄224186 > MAX1457AWI+ (MAXIM INTEGRATED PRODUCTS INC) 0.1% Accurate Signal Conditioner for Piezoresistive Sensor Compensation PDF資料下載
參數資料
| 型號： | MAX1457AWI+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | 0.1% Accurate Signal Conditioner for Piezoresistive Sensor Compensation |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封裝： | SOP-28 |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 93K |
| 代理商： | MAX1457AWI+ |
MAX1457
7) Perform curve-fitting to test data.
8) Based on a curve-fit algorithm, calculate up to 120
sets of offset and FSO correcting values.
9) Download correction coefficients to transducer
EEPROM.
10) Perform a final test.
The resulting transducer temperature errors are limited by
the following factors:
Number of selected segments for compensation (up to
120).
Accuracy of the curve fitting, which depends on the
algorithm used, the number of test temperatures, and
the sensor temperature error’s shape.
Repeatability of the sensor performance. This will limit
the MAX1457’s accuracy.
Sensor Calibration and
Compensation Example
Calibration and compensation requirements for a sen-
sor involve conversion of the sensor-specific perfor-
mance into a normalized output curve. An example of
the MAX1457’s capabilities is shown in Table 1.
As shown in Table 1, a repeatable piezoresistive sensor
with an initial offset of 16.4mV and FSO of 55.8mV was
converted into a compensated transducer (utilizing the
piezoresistive sensor with the MAX1457) with an offset
of 0.500V and a span of 4.000V. Nonlinear sensor offset
and FSO temperature errors, which were on the order
of 4% to 5% FSO, were reduced to under ±0.1% FSO.
The graphs in Figure 8 show the output of the uncom-
pensated sensor and the output of the compensated
transducer.
0.1%-Accurate Signal Conditioner
for Piezoresistive Sensor Compensation
10
______________________________________________________________________________________
MAX1457
EDO
VOUT
VDD
MCS
MODULE 1
EEPROM
EDI
ECLK
ECS
VSS
VDD
VSS
TEST
OVEN
MAX1457
EDO
VOUT
MCS
MODULE 2
EEPROM
EDI
ECLK
EDI
EDO
VOUT
DIGITAL
MULTIPLEXER
+5V
ECS1
ECS[1:N], MCS[1:N]
ECS2
MCS1
MCS2
ECS N
MCS N
ECLK
ECS
MAX1457
EDO
VOUT
MCS
MODULE N
EEPROM
EDI
ECLK
ECS
DVM
Figure 7. Automated Test System Concept
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1459CAP+T | 2-Wire, 4-20mA Smart Signal Conditioner |
| MAX1459AAP+T | 2-Wire, 4-20mA Smart Signal Conditioner |
| MAX1459CAP+ | 2-Wire, 4-20mA Smart Signal Conditioner |
| MAX1459AAP+ | 2-Wire, 4-20mA Smart Signal Conditioner |
| MAX147BEAP+ | +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1457CCJ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1457EVKIT-NS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX14580EETE+C77 | 制造商:Maxim Integrated Products 功能描述:USB BATTERY CHARGER DETECTORS - Rail/Tube |
| MAX14581EWC+T | 功能描述:USB 接口集成電路 3/5 Wire Full Speed USB Trnsvr RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MAX14582EWC+T | 功能描述:USB 接口集成電路 3/5 Wire Full Speed USB Trnsvr RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。