- 您現在的位置：買賣IC網 > PDF目錄11789 > MAX14502AETL+ (Maxim Integrated Products)IC CARD READER USB-SD 40-TQFN PDF資料下載
參數資料
| 型號： | MAX14502AETL+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 26/41頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CARD READER USB-SD 40-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 應用： | USB |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 1.8 V ~ 3.3 V |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-TQFN-EP（5x5） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
MAX14500–MAX14503
Hi-Speed USB-to-SD Card
Readers with Bypass
32
______________________________________________________________________________________
Power-Supply Modes
The MAX14500–MAX14503 have four power-supply
inputs (Table 6). Bypass VCC, VIO, VSD, and VTM with
high-frequency, surface-mount ceramic capacitors as
close as possible to the supply pins.
Power-supply inputs:
1) VTM USB Transceiver Power. This supply powers the
USB analog switches, PLL subsystem, and the USB
2.0 transceiver. This regulator can be internal to a
power-management IC, or it can be discrete and is
recommended to be powered from USB VBUS. This
supply must be present when the MAX14500–
MAX14503 are used in Card Reader mode to pass
USB signals in Pass Thru mode.
2) VCC Digital Logic Power. This supply powers the
digital logic/internal microcontroller/flash memory.
There is an internal +1.8V LDO (CLDO) with shut-
down controlled by the state of the MODE input and
internal logic.
3) VSD SD Card Power. This supply powers the SD
card level translator and SD card switches. VSD
needs to be present to pass SD signals in Pass Thru
mode.
4) VIO Host Interface Power. This supply powers the
digital I/O and I2C interface.
Power modes:
1) Idle. Only VIO is required to be present. I2C registers
can be updated, but no operation is possible.
2) Pass Thru Mode. VIO needs to be present so the
voltage level at MODE can be detected. To allow
USB pass thru, the VTM supply needs to be present.
To allow SD pass thru, VSD supply needs to be pre-
sent. Each supply is independent from the others
and no power-supply sequencing is required.
3) Card Reader Mode. All supplies are needed. When
the card reader is actively transferring data, this mode
draws the most current, mainly from VCC and VTM.
Layout Considerations
The MAX14500–MAX14503 support Hi-Speed USB and
requires careful PCB layout. Use controlled-impedance
matched traces of equal lengths to the USB connector
with no discontinuities and a minimum number of
feedthroughs. All SD traces (CLK, CMD, DAT_) should
be of equal lengths and as short as possible.
Choosing Pullup Resistors
I2C requires pullup resistors to provide a logic-high level
to data and clock lines. There are tradeoffs between
power dissipation and speed, and a compromise must
be made in choosing pullup resistor values. Every
device connected to the bus introduces some capaci-
tance, even when the device is not in operation. I2C
specifies 300ns rise time to go from low to high (30% to
70%) for fast mode, which is defined for data rates up to
400kbps. To meet the rise time requirement, choose
pullup resistors so the rise time (tR) is less than 300ns
where tR
≈ 0.85 x RPULLUP x CBUS. If the transition time
becomes too slow, the setup and hold times may not be
met and waveforms may not be recognized.
SUPPLY
FUNCTION
RANGE (V)
VTM
USB transceiver and USB
switch power
+2.91 to +3.4
VCC
Digital core 1.8V LDO
+2.1 to +3.6
VSD
SD card level translator and SD
switches
+2.0 to +3.6
VIO
Host microprocessor level
translator
+1.5 to +3.6
Table 6. Power-Supply Inputs
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/24WD19S | CONN RCPT 19POS JAM NUT W/SCKT |
| D38999/24WD19SN | CONN RCPT 19POS JAM NUT W/SCKT |
| MAX6818EAP+ | IC DEBOUNCER SWITCH OCTAL 20SSOP |
| VI-BTK-IX-F1 | CONVERTER MOD DC/DC 40V 75W |
| VI-BTK-IW-F4 | CONVERTER MOD DC/DC 40V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX14502AETL+ | 功能描述:接口 - 專用 High speed USB to FS-USB RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX14502AETL+T | 功能描述:接口 - 專用 High speed USB to FS-USB RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX14502EVKIT+ | 功能描述:界面開發工具 MAX14502 Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX14503AEWN+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX14503ETL+ | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。