- 您現在的位置：買賣IC網 > PDF目錄9499 > MAX1407CAI+ (Maxim Integrated Products)IC DAS 16BIT LP 28-SSOP PDF資料下載
參數資料
| 型號： | MAX1407CAI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/48頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAS 16BIT LP 28-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 46 |
| 類型： | 數據采集系統（DAS） |
| 分辨率（位）： | 16 b |
| 采樣率（每秒）： | 60 |
| 數據接口： | 串行 |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 2.7 V ~ 3.6 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
MAX1407/MAX1408/MAX1409/MAX1414
Low-Power, 16-Bit Multichannel DAS with
Internal Reference,10-Bit DACs, and RTC
______________________________________________________________________________________
21
Internal/External Reference
The MAX1407/MAX1408/MAX1409/MAX1414 have an
internal low-drift +1.25V reference used for both ADC
and DAC conversion. The buffered reference output
can be used as a reference source for other devices in
the system. The internal reference requires a 4.7F low-
ESR ceramic capacitor or tantalum capacitor connect-
ed between REF and AGND. For applications that
require increased accuracy, power-down the internal
reference by writing a 0 to the REFE bit of the Power1
register and connect an external reference source to
REF. The valid external reference voltage range is
1.25V ±100mV.
Crystal Oscillator
The on-chip oscillator requires an external crystal (or
resonator) connected between CLKIN and CLKOUT
with an operating frequency of 32.768kHz. This oscilla-
tor is used for the RTC, alarm, signal-detect compara-
tor, and PLL. The oscillator is operational down to 1.8V.
In any crystal-based oscillator circuit, the oscillator fre-
quency is based on the characteristics of the crystal. It
is important to select a crystal that meets the design
requirements, especially the capacitive load (CL) that
must be placed across the crystal pins in order for the
crystal to oscillate at its specified frequency. CL is the
capacitance that the crystal needs to “see” from the
oscillator circuit; it is not the capacitance of the crystal
itself. The MAX1407/MAX1408/MAX1409/MAX1414
have 6pF of capacitance across the CLKIN and CLK-
OUT pins. Choose a crystal with a 32.768kHz oscillation
frequency and a 6pF capacitive load such as the C-
002RX32-E from Epson Crystal. Using a crystal with a
CL that is larger than the load capacitance of the oscil-
lator circuit will cause the oscillator to run faster than
the specified nominal frequency of the crystal.
Conversely, using a crystal with a CL that is smaller
than the load capacitance of the oscillator circuit will
cause the oscillator to run slower than the specified
nominal frequency of the crystal.
Phase-Locked Loop (PLL) and FOUT
An on-board phase-locked loop generates a
2.4576MHz clock at FOUT from the 32.768kHz crystal
oscillator. FOUT can be used to clock a P or other dig-
ital circuitry. Connect an 18nF ceramic capacitor from
CPLL to AVDD to create the 2.4576MHz clock signal at
FOUT. To power down the PLL, clear PLLE in the
Power2 register (see Power2 Register) or write to the
Sleep register. FOUT will be active for 1.95ms (tDFOF)
after receiving either power-down command and then
go low. This provides extra clock signals to the P to
complete a shutdown sequence. The PLL is active in all
modes except the sleep mode (see Power Modes). To
reactivate the PLL, the following conditions must be
met: AVDD is greater than the low VDD voltage monitor
threshold, RESET is deasserted, and the PLLE bit is
equal to “1”. FOUT is enabled 31.25ms (tDFON) after
the PLL is activated. At initial power-up, the PLL is
enabled. If RESET is asserted while the PLL is running,
the PLL does not shut down.
Real-Time Clock (RTC)
The integrated RTC provides the current second,
minute, hour, date, month, day, year, century, and mil-
lenium information. An internally generated reference
clock of 1.024kHz (derived from the 32.768kHz crystal)
drives the RTC. The RTC operates in either 24-hour or
12-hour format with an AM/PM indicator (see RTC_Hour
Register). An internal calendar compensates for months
with less than 31 days and includes leap year correc-
tion through the year 9999. The RTC operates from a
supply voltage of +1.8V to +3.6V and consumes less
than 1A current.
Time of Day Alarm
The MAX1407/MAX1408/MAX1409/MAX1414 offer a time
of day alarm which generates an interrupt when the RTC
reaches a preset combination of seconds, minutes,
hours, and day (see Alarm Registers). In addition to set-
ting a “single-shot” alarm, the Time of Day Alarm can
also be programmed to generate an alarm every sec-
ond, minute, hour, day, or week. “Don’t care” states can
be inserted into one or more fields if it is desired for them
to be ignored for the alarm condition. The Time of Day
Alarm wakes up the device into Standby mode if it is in
Sleep mode. The Time of Day Alarm operates from a
supply voltage of +1.8V to +3.6V.
Interrupt (IIN
NT
T)
INT indicates one of three conditions. After receiving a
valid interrupt (INT goes low), read the Status register
and the Al_Status register (if the alarm is enabled) to
identify the source of the interrupt. The three sources of
interrupts are from the CLK, SDC, and ALIRQ bits.
PLL Ready
On power-up, INT is high. 7.82ms (tDFI) after the PLL
output appears on FOUT, INT goes low (see Figure 15).
The CLK bit of the Status register is set to “1” after
FOUT is enabled. Reading the Status register clears the
CLK bit. INT remains low until the device detects a start
bit through the serial interface from the P. The purpose
of this interrupt is to inform the P that the FOUT clock
signal is present.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1414CAI+ | IC DAS 16BIT LP 28-SSOP |
| NBXDPA019LN1TAG | IC CLK XO LVDS 125/250MHZ 6CLCC |
| MAX181CCQH+D | IC DAS 12BIT 100KSPS 44-PLCC |
| 74AC138SC | IC DECODER/DEMUX 1OF8 16-SOIC |
| MAX181CCQH-D | IC DAS 6CH 12BIT 100KHZ 44-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1407CAI+ | 功能描述:ADC / DAC多通道 16-Bit 4Ch 60sps 1.35V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1407CAI+T | 功能描述:ADC / DAC多通道 16-Bit 4Ch 60sps 1.35V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1407CAI-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1407EAI+ | 制造商:Maxim Integrated Products 功能描述:LOW-POWER 16-BIT MULTICHANNEL DAS - Rail/Tube |
| MAX1407EAI+T | 制造商:Maxim Integrated Products 功能描述:LOW-POWER 16-BIT MULTICHANNEL DAS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。