- 您現在的位置：買賣IC網 > PDF目錄69017 > MAQ31753FXXXX (DYNEX SEMICONDUCTOR LTD) 4 CHANNEL(S), 16 MHz, DMA CONTROLLER, CQFP84 PDF資料下載
參數資料
| 型號： | MAQ31753FXXXX |
| 廠商： | DYNEX SEMICONDUCTOR LTD |
| 元件分類： | DMA控制器 |
| 英文描述： | 4 CHANNEL(S), 16 MHz, DMA CONTROLLER, CQFP84 |
| 封裝： | QFP-84 |
| 文件頁數： | 27/31頁 |
| 文件大小： | 238K |
| 代理商： | MAQ31753FXXXX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁
MA31753
5/31
3.10 SOFTWARE PROGRAMMING
DMA requests can be generated in software by writing the
CRQP bit in the Channel Status register. If the channel is
active, the DMA will then request bus control. If the DREQN
signal on that channel is not active, the DMA finishes the cycle
as soon as the memory is ready. There is no handshaking with
the IO port. DACKN is deasserted when the memory is ready.
If DREQN is asserted but is masked, the handshaking is active
and operates normally.
Interrupts can be generated in software by setting either a
channel EOT flag or any error flag. This can only be done
when the DMA is in PEND_CHAIN mode. If an error flag is set,
the device goes straight to ERROR mode. If the EOT flag is
set, the device looks as if it has completed the transfer. It will
then just sit and wait for the EOT flag to be cleared before
entering IDLE mode. If both flags are set simultaneously, the
device remains in PEND_CHAIN mode. Setting an error flag
when EOT is set resets EOT and the device goes to ERROR
mode. Setting EOT when an error flag is set clears the error
and the DMA sits in the finish transfer mode.
3.11 CASCADING DMA CONTROLLERS
DMA controllers are cascaded in series. For each DMA
added, an extra 4 channels become available. To cascade the
devices, the strobes, control signals and address and data
busses are connected in parallel. Of the bus arbitration
signals, LOCKN and GRANTN should be connected in parallel
and REQINN, GEINN and GEOUTN shoudl be daisy-chained.
INTRN and PEN can either be ORed together with external
glue logic or input to seperate CPU interrupts. Figure 3 shows
the cascade connections.
Figure 3: Cascading DMA Controllers
Bus
Arbiter
DMAC 1
DMAC 2
REQN
REQINN
GEOUTN
GEINN
DREQN[0:3]
D
A
CKN[0:3]
Bus
Interf
ace
Signals
DREQN[0:3]
D
A
CKN[0:3]
Bus
Interf
ace
Signals
GRANTN
44
4
相關PDF資料 |
PDF描述 |
|---|---|
| MAR31753FXXXX | 4 CHANNEL(S), 16 MHz, DMA CONTROLLER, CQFP84 |
| MAS31753FXXXX | 4 CHANNEL(S), 16 MHz, DMA CONTROLLER, CQFP84 |
| MAR28155CXXXX | 24 I/O, PIA-GENERAL PURPOSE, CDIP40 |
| MAR28155LXXXX | 24 I/O, PIA-GENERAL PURPOSE, CQCC44 |
| MAS28155CXXXX | 24 I/O, PIA-GENERAL PURPOSE, CDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAQ3203 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:High-Brightness LED Driver Controller with High-Side Current Sense |
| MAQ3203YM | 功能描述:LED照明驅動器 Automotive Qualified HBLED Driver Controller RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAQ3203YM TR | 功能描述:LED照明驅動器 Automotive Qualified HBLED Driver Controller RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAQ3203YM-VAO | 功能描述:IC LED DRIVER CTRLR DIM 8SOIC 制造商:microchip technology 系列:汽車級，AEC-Q100 包裝:管件 零件狀態:在售 類型:DC DC 控制器 拓?fù)?降壓 內部開關:無 輸出數:1 電壓 - 供電（最低）:4.5V 電壓 -?供電（最高）:42V 電壓 - 輸出:- 電流 - 輸出/通道:- 頻率:1.5MHz 調光:PWM 應用:汽車級，照明 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 標準包裝:95 |
| MAQ3690CC | 制造商:DYNEX 制造商全稱:Dynex Semiconductor 功能描述:1553B Bus Controller/Remote Terminal |
發布緊急采購，3分鐘左右您將得到回復。