- 您現在的位置：買賣IC網 > PDF目錄383303 > M50FW040NB5TP (意法半導體) 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory PDF資料下載
參數資料
| 型號： | M50FW040NB5TP |
| 廠商： | 意法半導體 |
| 英文描述： | 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| 中文描述： | 4兆位（512 KB的× 8，均勻塊）3 - V電源供電的閃存固件樞紐 |
| 文件頁數： | 24/53頁 |
| 文件大?。?/td> | 278K |
| 代理商： | M50FW040NB5TP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
Command interface
M50FW040
24/53
4.7
Program/Erase Suspend command
The Program/Erase Suspend command can be used to pause a Program or Erase operation.
One Bus Write cycle is required to issue the Program/Erase Suspend command and pause
the Program/Erase Controller. Once the command is issued it is necessary to poll the
Program/Erase Controller Status bit to find out when the Program/Erase Controller has
paused; no other commands will be accepted until the Program/Erase Controller has
paused. After the Program/Erase Controller has paused, the memory will continue to output
the Status Register until another command is issued.
During the polling period between issuing the Program/Erase Suspend command and the
Program/Erase Controller pausing it is possible for the operation to complete. Once
Program/Erase Controller Status bit indicates that the Program/Erase Controller is no longer
active, the Program Suspend Status bit or the Erase Suspend Status bit can be used to
determine if the operation has completed or is suspended. For timing on the delay between
issuing the Program/Erase Suspend command and the Program/Erase Controller pausing
see
Table 12
.
During Program/Erase Suspend the Read Memory Array, Read Status Register, Read
Electronic Signature and Program/Erase Resume commands will be accepted by the
Command Interface. Additionally, if the suspended operation was Erase then the Program
command will also be accepted; only the blocks not being erased may be read or
programmed correctly.
See
Figure 19: Program Suspend & Resume flowchart and pseudo code
, and
Figure 21:
Erase Suspend & Resume flowchart and pseudo code
, for suggested flowcharts on using
the Program/Erase Suspend command.
4.8
Program/Erase Resume command
The Program/Erase Resume command can be used to restart the Program/Erase Controller
after a Program/Erase Suspend operation has paused it. One Bus Write cycle is required to
issue the Program/Erase Resume command. Once the command is issued subsequent Bus
Read operations read the Status Register.
Table 6.
Read electronic signature
Code
Address
Data
Manufacturer code
00000h
20h
Device code
00001h
2Ch
相關PDF資料 |
PDF描述 |
|---|---|
| M50LPW116 | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW116N | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW116N1T | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW116N5T | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M51131L | 2 CHANNEL ELECTRONIC VOLUME BALANCE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW080 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K1 | 功能描述:閃存 3.6V 8M (1Mx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FW080K1G | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。