- 您現在的位置：買賣IC網 > PDF目錄383303 > M50FW040NB5G (意法半導體) 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory PDF資料下載
參數資料
| 型號： | M50FW040NB5G |
| 廠商： | 意法半導體 |
| 英文描述： | 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| 中文描述： | 4兆位（512 KB的× 8，均勻塊）3 - V電源供電的閃存固件樞紐 |
| 文件頁數： | 15/53頁 |
| 文件大?。?/td> | 278K |
| 代理商： | M50FW040NB5G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
M50FW040
Signal descriptions
15/53
2.2.6
Ready/Busy Output (RB)
The Ready/Busy pin gives the status of the memory’s Program/Erase Controller. When
Ready/Busy is Low, V
OL
, the memory is busy with a Program or Erase operation and it will
not accept any additional Program or Erase command except the Program/Erase Suspend
command. When Ready/Busy is High, V
OH
, the memory is ready for any Read, Program or
Erase operation.
2.3
Supply signal descriptions
The Supply Signals are the same for both interfaces.
2.3.1
V
CC
supply voltage
The V
CC
Supply Voltage supplies the power for all operations (Read, Program, Erase etc.).
The Command Interface is disabled when the V
CC
Supply Voltage is less than the Lockout
Voltage, V
LKO
. This prevents Bus Write operations from accidentally damaging the data
during power up, power down and power surges. If the Program/Erase Controller is
programming or erasing during this time then the operation aborts and the memory contents
being altered will be invalid. After V
CC
becomes valid the Command Interface is reset to
Read mode.
A 0.1μF capacitor should be connected between the V
CC
Supply Voltage pins and the V
SS
Ground pin to decouple the current surges from the power supply. Both V
CC
Supply Voltage
pins must be connected to the power supply. The PCB track widths must be sufficient to
carry the currents required during program and erase operations.
2.3.2
V
PP
optional supply voltage
The V
PP
Optional Supply Voltage pin is used to select the Fast Erase option of the memory
and to protect the memory. When V
PP
< V
PPLK
Program and Erase operations cannot be
performed and an error is reported in the Status Register if an attempt to change the
memory contents is made. When V
PP
= V
CC
Program and Erase operations take place as
normal. When V
PP
= V
PPH
Fast Erase operations are used. Any other voltage input to V
PP
will result in undefined behavior and should not be used.
V
PP
should not be set to V
PPH
for more than 80 hours during the life of the memory.
2.3.3
V
SS
ground
V
SS
is the reference for all the voltage measurements.
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW040NB5P | 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| M50FW040NB5TG | 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| M50FW040NB5TP | 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| M50LPW116 | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW116N | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW040NB5P | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| M50FW040NB5TG | 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FW040NB5TP | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| M50FW080 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。