參數資料
型號: M41ST85
廠商: 意法半導體
英文描述: 5.0 OR 3.0V, 512 bit 64 x 8 SERIAL RTC and NVRAM SUPERVISOR
中文描述: 5.0或3.0V,512位64 × 8串行時鐘和NVRAM督導員
文件頁數: 21/33頁
文件大小: 464K
代理商: M41ST85
21/33
M41ST85Y, M41ST85W
Figure 19. Back-Up Mode Alarm Waveform
Watchdog Timer
The watchdog timer can be used to detect an out-
of-control microprocessor. The user programs the
watchdog timer by setting the desired amount of
time-out into the Watchdog Register, address 09h.
Bits BMB4-BMB0 store a binary multiplier and the
two lower order bits RB1-RB0 select the resolu-
tion, where 00=1/16 second, 01=1/4 second, 10=1
second, and 11=4 seconds. The amount of time-
out is then determined to be the multiplication of
the five-bit multiplier value with the resolution. (For
example: writing 00001110 in the Watchdog Reg-
ister = 3*1 or 3 seconds).
Note:
The accuracy of the timer is within ± the se-
lected resolution.
If the processor does not reset the timer within the
specified period, the M41ST85Y/W sets the WDF
(Watchdog Flag) and generates a watchdog inter-
rupt or a microprocessor reset.
The most significant bit of the Watchdog Register
is the Watchdog Steering Bit (WDS). When set to
a '0,' the watchdog will activate the IRQ/FT/OUT
pin when timed-out. When WDS is set to a '1,' the
watchdog will output a negative pulse on the RST
pin for t
REC
. The Watchdog register, FT, AFE, ABE
and SQWE Bits will reset to a '0' at the end of a
Watchdog time-out when the WDS Bit is set to a
'1.'
The watchdog timer can be reset by two methods:
1) a transition (high-to-low or low-to-high) can be
applied to the Watchdog Input pin (WDI) or 2) the
microprocessor can perform a WRITE of the
Watchdog Register. The time-out period then
starts over.
Note:
The WDI pin should be tied to V
SS
if not
used.
In order to perform a software reset of the watch-
dog timer, the original time-out period can be writ-
ten into the Watchdog Register, effectively
restarting the count-down cycle.
Should the watchdog timer time-out, and the WDS
Bit is programmed to output an interrupt, a value of
00h needs to be written to the Watchdog Register
in order to clear the IRQ/FT/OUT pin. This will also
disable the watchdog function until it is again pro-
grammed correctly. A READ of the Flags Register
will reset the Watchdog Flag (Bit D7; Register
0Fh).
The watchdog function is automatically disabled
upon power-up and the Watchdog Register is
cleared. If the watchdog function is set to output to
the IRQ/FT/OUT pin and the frequency test func-
tion is activated, the watchdog function prevails
and the frequency test function is denied.
AI03920
VCC
VPFD
IRQ/FT/OUT
ABE, AFE Bits in Interrupt Register
AF bit in Flags Register
HIGH-Z
VSO
HIGH-Z
tREC
相關PDF資料
PDF描述
M41ST85WMH6TR RECTIFIER FAST-RECOVERY SINGLE 1A 400V 30A-ifsm 1.3V-vf 40ns 10uA-ir DO-41 1K/BULK
M41ST85WMH6 RECTIFIER FAST-RECOVERY SINGLE 1A 300V 30A-ifsm 1.3V-vf 40ns 10uA-ir DO-41 5K/REEL-13
M41ST87W 5.0, 3.3, or 3.0V, 1280 bit (160 x8) Secure Serial RTC and NVRAM Supervisor with Tamper Detection
M41ST87WMX6 RECTIFIER SCHOTTKY SINGLE 10A 25V 200A-Ifsm 0.45Vf 1A-IR D2PAK 50/TUBE
M41ST87WMX6TR 5.0, 3.3, or 3.0V, 1280 bit (160 x8) Secure Serial RTC and NVRAM Supervisor with Tamper Detection
相關代理商/技術參數
參數描述
M41ST85W 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 OR 3.0V, 512 bit 64 x 8 SERIAL RTC and NVRAM SUPERVISOR
M41ST85W_06 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3.0/3.3V I2C Combination Serial RTC, NVRAM Supervisor and Microprocessor Supervisor
M41ST85W_07 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3.0/3.3V I2C combination serial RTC, NVRAM supervisor and microprocessor supervisor
M41ST85W_11 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3.0/3.3 V I2C combination serial RTC, NVRAM supervisor and microprocessor supervisor
M41ST85WMH 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 OR 3.0V, 512 bit 64 x 8 SERIAL RTC and NVRAM SUPERVISOR