參數資料
型號: M41ST84WMQ6E
廠商: 意法半導體
英文描述: 3.0/3.3V I2C Serial RTC with Supervisory Functions
中文描述: 3.0/3.3V I2C串行實時時鐘具有監督職能
文件頁數: 17/29頁
文件大?。?/td> 176K
代理商: M41ST84WMQ6E
17/29
M41ST84W
Setting Alarm Clock Registers
Address locations 0Ah-0Eh contain the alarm set-
tings. The alarm can be configured to go off at a
prescribed time on a specific month, date, hour,
minute, or second, or repeat every year, month,
day, hour, minute, or second. It can also be pro-
grammed to go off while the M41ST84W is in the
battery back-up to serve as a system wake-up call.
Bits RPT5-RPT1 put the alarm in the repeat mode
of operation.
Table 4., page 17
shows the possible
configurations. Codes not listed in the table default
to the once per second mode to quickly alert the
user of an incorrect alarm setting.
When the clock information matches the alarm
clock settings based on the match criteria defined
by RPT5-RPT1, the AF (Alarm Flag) is set. If AFE
(Alarm Flag Enable) is also set, the alarm condi-
tion activates the IRQ/FT/OUT pin.
Note:
If the address pointer is allowed to incre-
ment to the Flag Register address, an alarm con-
dition will not cause the Interrupt/Flag to occur until
the address pointer is moved to a different ad-
dress. It should also be noted that if the last ad-
dress written is the “Alarm Seconds,” the address
pointer will increment to the Flag address, causing
this situation to occur.
The IRQ/FT/OUT output is cleared by a READ to
the Flags Register as shown in
Figure 15.
. A sub-
sequent READ of the Flags Register is necessary
to see that the value of the Alarm Flag has been
reset to '0.'
The IRQ/FT/OUT pin can also be activated in the
battery back-up mode. The IRQ/FT/OUT will go
low if an alarm occurs and both ABE (Alarm in Bat-
tery Back-up Mode Enable) and AFE are set. The
ABE and AFE Bits are reset during power-up,
therefore an alarm generated during power-up will
only set AF. The user can read the Flag Register
at system boot-up to determine if an alarm was
generated while the M41ST84W was in the dese-
lect mode during power-up.
Figure 16., page 18
il-
lustrates the back-up mode alarm timing.
Figure 15. Alarm Interrupt Reset Waveform
Table 4. Alarm Repeat Modes
RPT5
RPT4
RPT3
RPT2
RPT1
Alarm Setting
1
1
1
1
1
Once per Second
1
1
1
1
0
Once per Minute
1
1
1
0
0
Once per Hour
1
1
0
0
0
Once per Day
1
0
0
0
0
Once per Month
0
0
0
0
0
Once per Year
AI03664
IRQ/FT/OUT
ACTIVE FLAG
0Fh
0Eh
10h
HIGH-Z
相關PDF資料
PDF描述
M41ST84W 3.0/3.3V I2C Serial RTC with Supervisory Functions(帶監視功能的3.0/3.3V I2C串行RTC)
M41ST84Y(中文) 512 bit (64 x 8) Serial RTC with Supervisory Functions
M41ST84 5.0 OR 3.0V, 512 bit (64 x 8) Serial RTC with supervisory functions(具有監控功能的5.0V或3.0V,512位(64 x 8)串行RTC)
M41ST85WMH6E 3.0/3.3V I2C Combination Serial RTC, NVRAM Supervisor and Microprocessor Supervisor
M41ST85WMH6F 3.0/3.3V I2C Combination Serial RTC, NVRAM Supervisor and Microprocessor Supervisor
相關代理商/技術參數
參數描述
M41ST84WMQ6F 功能描述:實時時鐘 Serial 512 (64x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41ST84WMQ6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3.0/3.3V I2C Serial RTC with Supervisory Functions
M41ST84WSH 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.0V, 512 bit 64 x 8 SERIAL RTC with SUPERVISORY FUNCTIONS
M41ST84Y 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.0V, 512 bit 64 x 8 SERIAL RTC with SUPERVISORY FUNCTIONS
M41ST84YMH 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.0V, 512 bit 64 x 8 SERIAL RTC with SUPERVISORY FUNCTIONS