參數資料
型號： M38C29FFFP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP64
封裝： 14 X 14 MM, PLASTIC, LQFP-64
文件頁數： 54/101頁
文件大小： 1529K
代理商： M38C29FFFP
56
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e parametric
limits
are
subject
to
change.
Table 11 Summary of 38C2 group’s flash memory version
FLASH MEMORY MODE
The 38C2 group’s flash memory version has an internal new
DINOR (DIvided bit line NOR) flash memory that can be rewritten
with a single power source when VCC is 4.5 to 5.5 V, and 2 power
sources when VCC is 3.0 to 4.5 V.
For this flash memory, three flash memory modes are available in
which to read, program, and erase: the parallel I/O and standard
serial I/O modes in which the flash memory can be manipulated
using a programmer and the CPU rewrite mode in which the flash
memory can be manipulated by the Central Processing Unit
(CPU).
Summary
Table 11 lists the summary of the 38C2 Group (flash memory ver-
sion).
This flash memory version has some blocks on the flash memory
as shown in Figure 61 and each block can be erased.
In addition to the ordinary User ROM area to store the MCU op-
eration control program, the flash memory has a Boot ROM area
that is used to store a program to control rewriting in CPU rewrite
and standard serial I/O modes. This Boot ROM area has had a
standard serial I/O mode control program stored in it when
shipped from the factory. However, the user can write a rewrite
control program in this area that suits the user’s application sys-
tem. This Boot ROM area can be rewritten in only parallel I/O
mode.
Item
Power source voltage (Vcc)
Program/Erase VPP voltage (VPP)
Flash memory mode
Erase block division
User ROM area
Boot ROM area
Program method
Erase method
Program/Erase control method
Number of commands
Number of program/Erase times
ROM code protection
Specifications
VCC = 2.5 to 5.5 V (Note 1)
VCC = 2.5 to (VCC at program/erase) + 0.5 V (Note 2)
VPP = 4.5 to 5.5 V, VCC = 3.0 to 5.5 V
3 modes; Parallel I/O mode, Standard serial I/O mode, CPU rewrite mode
Refer to Fig. 61.
Not divided (4K bytes) (Note 3)
In units of bytes
Block erase
Program/Erase control by software command
5 commands
100 times
Available in parallel I/O mode and standard serial I/O mode
Notes 1: It is the rating value when Vcc = 5.0 to 5.5 V at program/erase.
2: It is the rating value when Vcc = 3.0 to 5.0 V at program/erase.
3: The Boot ROM area has had a standard serial I/O mode control program stored in it when shipped from the factory. This Boot ROM area can be
erased and written in only parallel I/O mode.
相關PDF資料
PDF描述
M38C29FFHP 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP64
M38C34M6AXXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
M38C37ECMFS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC80
M38C37ECAFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80
M38C37ECMFP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
M38C29FFHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29MC-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29MC-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29RLFS 功能描述:EMULATOR MCU FOR A-VERSION 38C2 RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M38C29T-64FPD 功能描述:DEV 100-PIN RFS/MCU TO 64-PIN 0. RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*