- 您現在的位置：買賣IC網 > PDF目錄370960 > M38B59MFH-P113FP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38B59MFH-P113FP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 27/69頁 |
| 文件大小： | 1011K |
| 代理商： | M38B59MFH-P113FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
MITSUBISHI MICROCOMPUTERS
38B5 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
27
PRELIMINARY
Notice: This s not a final specification.
Some parametric imits are subject to change.
(2) 8-bit Serial I/O Mode
Address 001B
16
is assigned to the serial I/O1 register.
When the internal synchronous clock is selected, a serial transfer
of the 8-bit serial I/O is started by a write signal to the serial I/O1
register (address 001B
16
).
The serial transfer status flag (b5 of address 001A
16
) of serial I/O1
control register 2 indicates the shift register status of serial I/O1,
and is set to “1” by writing into the serial I/O1 register, which be-
comes a transfer start trigger and reset to “0” after completion of 8-
bit transfer. At the same time, a serial I/O1 interrupt request occurs.
When the external synchronous clock is selected, the contents of
the serial I/O1 register are continuously shifted while transfer clocks
are input to S
CLK1
. Therefore, the clock needs to be controlled ex-
ternally.
(3) Automatic Transfer Serial I/O Mode
The serial I/O1 automatic transfer controller controls the write and
read operations of the serial I/O1 register, so the function of ad-
dress 001B
16
is used as a transfer counter (1-byte units).
When performing serial transfer through the serial I/O automatic
transfer RAM (addresses 0F00
16
to 0FFF
16
), it is necessary to set
the serial I/O1 automatic transfer data pointer (address 0018
16
)
beforehand.
Input the low-order 8 bits of the first data store address to be seri-
ally transferred to the automatic transfer data pointer set bits.
When the internal synchronous clock is selected, the transfer inter-
val for each 1-byte data can be set by the automatic transfer inter-
val set bits (b0 to b4 of address 001C
16
) of serial I/O1 control regis-
ter 3 in the following cases:
1. When using no handshake signal
2. When using the S
RDY1
output, S
BUSY1
output, and S
STB1
output
of the handshake signal independently
3. When using a combination of S
RDY1
output and S
STB1
output or a
combination of S
BUSY1
output and S
STB1
output of the handshake
signal
It is possible to select one of 32 different values, namely 2 to 33
cycles of the transfer clock, as a setting value.
When using the S
BUSY1
output and selecting the S
BUSY1
output
S
STB1
output function selection bit (b4 of address 001A
16
) of serial
I/O1 control register 2 as the signal for all transfer data, provided
that the automatic transfer interval setting is valid, a transfer inter-
val is placed before the start of transmission/reception of the first
data and after the end of transmission/reception of the last data.
For S
STB1
output, regardless of the contents of the S
BUSY1
output
S
STB1
output function selection bit (b4), the transfer interval for each
1-byte data is longer than the set value by 2 cycles.
Furthermore, when using a combination of S
BUSY1
output and S
STB1
output as a signal for all transfer data, the transfer interval after the
end of transmission/reception of the last data is longer than the set
value by 2 cycles.
When the external synchronous clock is selected, automatic trans-
fer interval setting is disabled.
After completion of the above bit setup, if the internal synchronous
clock is selected, automatic serial transfer is started by writing the
value of “number of transfer bytes - 1” into the transfer counter
(address 001B
16
).
When the external synchronous clock is selected, write the value of
“number of transfer bytes - 1” into the transfer counter and input an
internal system clock interval of 5 cycles or more. After that, input
transfer clock to S
CLK1
.
As a transfer interval for each 1-byte data transfer, input an internal
system clock interval of 5 cycles or more from the clock rise time of
the last bit.
Regardless of whether the internal or external synchronous clock
is selected, the automatic transfer data pointer and the transfer
counter are decremented after each 1-byte data is received and
then written into the automatic transfer RAM. The serial transfer
status flag (b5 of address 001A
16
) is set to “1” by writing data into
the transfer counter. Writing data becomes a transfer start trigger,
and the serial transfer status flag is reset to “0” after the last data is
written into the automatic transfer RAM. At the same time, a serial
I/O1 interrupt request occurs.
The values written in the automatic transfer data pointer set bits
(b0 to b7 of address 0018
16
) and the automatic transfer interval set
bits (b0 to b4 of address 001C
16
) are held in the latch.
When data is written into the transfer counter, the values latched in
the automatic transfer data pointer set bits (b0 to b7) and the auto-
matic transfer interval set bits (b0 to b4) are transferred to the
decrement counter.
Fig. 22 Structure of Serial I/O1 Automatic Transfer Data Pointer
b7
b0
Serial I/O1 automatic transfer data pointer
(SIO1DP: address 0018
16
)
Automatic transfer data pointer set bits
Specify the low-order 8 bits of the first data store address on the serial I/O automatic
transfer RAM. Data is written into the latch and read from the decrement counter.
相關PDF資料 |
PDF描述 |
|---|---|
| M38B57MCH-P202FP | RES,Carbon Film,51Ohms,350WV,5+/-% Tol |
| M38B57MCH-P218FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38B57 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38B53M4-059FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38B53M4-060FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38B79MFA053 | 制造商:Panasonic Industrial Company 功能描述:SUB ONLY IC |
| M38C13E6FP | 功能描述:IC 740 MCU OTP 24K 64LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| M38C13E6HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C13RLFS | 制造商:Renesas Electronics Corporation 功能描述:EMULATION MCU/8BIT CMOS EMULATION CHIP - Bulk |
| M38C24M4-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。