參數資料
型號： M38B59MFH-E111FP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 53/69頁
文件大?。?/td> 1011K
代理商： M38B59MFH-E111FP
MITSUBISHI MICROCOMPUTERS
38B5 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
53
PRELIMINARY
Notice: This s not a final specification.
Some parametric imits are subject to change.
Fig. 62 Structure of Watchdog Timer Control Register
“0,” the underflow signal of watchdog timer L becomes the count
source. The detection time is set then to f(X
IN
) = 2.1 s at 4 MHz
frequency and f(X
CIN
) = 512 s at 32 kHz frequency.
When this bit is set to “1,” the count source becomes the signal
divided by 8 for f(X
IN
) (or divided by 16 for f(X
CIN
)). The detection
time in this case is set to f(XIN) = 8.2 ms at 4 MHz frequency and
f(XCIN) = 2 s at 32 KHz frequency. This bit is cleared to “0” after
resetting.
(3) Operation of STP instruction disable bit
Bit 6 of the watchdog timer control register (address 002B
16
) permits
disabling the STP instruction when the watchdog timer is in opera-
tion.
When this bit is “0,” the STP instruction is enabled.
When this bit is “1,” the STP instruction is disabled.
Once the STP instruction is executed, an internal resetting occurs.
When this bit is set to “1,” it cannot be rewritten to “0” by program.
This bit is cleared to “0” after resetting.
I
Note
When releasing the stop mode, the watchdog timer performs its count
operation even in the stop release waiting time. Be careful not to
cause the watchdog timer H to underflow in the stop release waiting
time, for example, by writing data in the watchdog timer control reg-
ister (address 002B
16
) before executing the STP instruction.
Fig. 61 Block Diagram of Watchdog Timer
X
IN
Data bus
X
CIN
“1”
“0”
Internal system clock
(Note)
“0”
“1”
1/8
Watchdog timer H count
source selection bit
Reset
circuit
STP instruction disable bit
STP instruction
Watchdog timer H (12)
16
” is set
“FFF
timer control
to.
Internal reset
RESET
Watchdog timer L (8)
Note: Either high-speed, middle-speed or low-speed mode is selected by bit 7 of CPU mode register.
“FF
16
” is set when
watchdog timer
1/2
b0
STP instruction disable bit
0: STP instruction enabled
1: STP instruction disabled
Watchdog timer H count source selection bit
0: Watchdog timer L underflow
1: f(X
IN
)/8 or f(X
CIN
)/16
Watchdog timer H (for read-out of high-order 6 bit)
Watchdog timer control register
(WDTCON : address 002B
16
)
b7
Watchdog Timer
The watchdog timer gives a mean of returning to the reset status
when a program cannot run on a normal loop (for example, because
of a software runaway). The watchdog timer consists of an 8-bit watch-
dog timer L and a 12-bit watchdog timer H.
G
Standard operation of watchdog timer
When any data is not written into the watchdog timer control register
(address 002B
16
) after resetting, the watchdog timer is in the stop
state. The watchdog timer starts to count down by writing an optional
value into the watchdog timer control register (address 002B
16
) and
an internal reset occurs at an underflow of the watchdog timer H.
Accordingly, programming is usually performed so that writing to the
watchdog timer control register (address 002B
16
) may be started
before an underflow. When the watchdog timer control register
(address 002B
16
) is read, the values of the 6 high-order bits of the
watchdog timer H, STP instruction disable bit, and watchdog timer H
count source selection bit are read.
(1) Initial value of watchdog timer
At reset or writing to the watchdog timer control register (address
002B
16
), a watchdog timer H is set to “FFF
16
” and a watchdog timer
L to “FF
16
.”
(2) Watchdog timer H count source selection bit operation
Bit 7 of the watchdog timer control register (address 002B
16
) permits
selecting a watchdog timer H count source. When this bit is set to
相關PDF資料
PDF描述
M38B59MFH-E112FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38B59MFH-P113FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38B57MCH-P202FP RES,Carbon Film,51Ohms,350WV,5+/-% Tol
M38B57MCH-P218FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38B57 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38B79MFA053 制造商:Panasonic Industrial Company 功能描述:SUB ONLY IC
M38C13E6FP 功能描述:IC 740 MCU OTP 24K 64LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
M38C13E6HP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C13RLFS 制造商:Renesas Electronics Corporation 功能描述:EMULATION MCU/8BIT CMOS EMULATION CHIP - Bulk
M38C24M4-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*