參數資料
型號: M38503E4SS
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述: 單芯片8位CMOS微機
文件頁數: 51/86頁
文件大?。?/td> 1193K
代理商: M38503E4SS
51
3850 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Software Commands
Table 14 lists the software commands. By entering a software com-
mand from the data I/O pins (D
0
D
7
) in Write mode, specify the con-
tent of the operation, such as erase or program operation, to be per-
formed.
The following explains the content of each software command.
Read Array Command (FF
16
)
The read array mode is entered by writing the command code
FF
16
in the first bus cycle. When an address to be read is input in one of
the bus cycles that follow, the content of the specified address is
output from the data I/O pins (D
0
D
7
).
The read array mode is retained intact until another command is writ-
ten.
The read array mode is also selected automatically when the device
is powered on and after it exits deep power down mode.
Command
Read array
Read status register
Clear status register
Program
All block erase
Block erase
Mode
Write
Write
Write
Write
Write
Write
Address
X
(Note 4)
X
X
X
X
X
Data
(D
0
to D
7
)
FF
16
70
16
50
16
40
16
20
16
20
16
Mode
Read
Write
Write
Write
Address
X
WA
(Note 2)
X
BA
(Note 3)
Data
(D
0
to D
7
)
SRD
(Note 1)
WD
(Note 2)
20
16
D0
16
First bus cycle
Second bus cycle
Notes 1:
SRD = Status Register Data
2:
WA = Write Address, WD = Write Data
3:
BA = Block Address (Enter the maximum address of each block)
4:
X denotes a given address in the user ROM area or boot ROM area.
Read Status Register Command (70
16
)
When the command code
70
16
is written in the first bus cycle, the
content of the status register is output from the data I/O pins (D
0
D
7
)
by a read in the second bus cycle. Since the content of the status
register is updated at the falling edge of OE or CE, the OE or CE
signal must be asserted each time the status is read. The status
register is explained in the next section.
Clear Status Register Command (50
16
)
This command is used to clear the bits SR4,SR5 of the status regis-
ter after they have been set. These bits indicate that operation has
ended in an error. To use this command, write the command code
50
16
in the first bus cycle.
Table 14 Software command list (parallel I/O mode)
Cycle number
1
2
1
2
2
2
相關PDF資料
PDF描述
M38503M4 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503MXH SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38507E8SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4H-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4H-XXXSP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38503G4AFP#U1 功能描述:IC 740/3850 MCU QZ-ROM 42SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI,I²C,UART/USART 外圍設備:POR,PWM,WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC(J 形引線) 包裝:帶卷 (TR)
M38503G4ASP#U1 功能描述:IC 740/3850 MCU QZ-ROM 42DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI,I²C,UART/USART 外圍設備:POR,PWM,WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC(J 形引線) 包裝:帶卷 (TR)
M38503M2404F 制造商:Panasonic Industrial Company 功能描述:IC
M38503M4A-210SP 制造商:Renesas Electronics Corporation 功能描述:
M38504E6FP 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 24K 42-SSOP - Trays