參數資料
型號: M381L1713FTM-CA2
元件分類: DRAM
英文描述: 16M X 72 DDR DRAM MODULE, 0.75 ns, DMA184
封裝: DIMM-184
文件頁數: 6/15頁
文件大?。?/td> 273K
代理商: M381L1713FTM-CA2
DDR SDRAM
128MB, 256MB Unbuffered DIMM
Rev. 1.0 March. 2004
Command Truth Table
(V=Valid, X=Don
′t Care, H=Logic High, L=Logic Low)
COMMAND
CKEn-1
CKEn
CS
RAS
CAS
WE BA0,1 A10/AP
A0 ~ A9
A11
Note
Register
Extended MRS
H
X
L
OP CODE
1, 2
Register
Mode Register Set
H
X
L
OP CODE
1, 2
Refresh
Auto Refresh
H
LL
LH
X
3
Self
Refresh
Entry
L
3
Exit
L
H
LH
HH
X
3
HX
X
3
Bank Active & Row Addr.
H
X
L
H
V
Row Address
(A0~A9, A11)
Read &
Column Address
Auto Precharge Disable
HX
L
H
L
H
V
L
Column
Address
4
Auto Precharge Enable
H
4
Write &
Column Address
Auto Precharge Disable
HX
L
H
L
V
L
Column
Address
4
Auto Precharge Enable
H
4, 6
Burst Stop
H
X
L
H
L
X
7
Precharge
Bank Selection
HX
L
H
L
VL
X
All Banks
X
H
5
Active Power Down
Entry
H
L
HX
X
LV
V
Exit
L
H
X
Precharge Power Down Mode
Entry
H
L
HX
X
LH
HH
Exit
L
H
HX
X
LV
V
DM
H
X
8
No operation (NOP) : Not defined
H
X
HX
X
9
LH
HH
9
Note : 1. OP Code : Operand Code. A0 ~ A11 & BA0 ~ BA1 : Program keys. (@EMRS/MRS)
2. EMRS/ MRS can be issued only at all banks precharge state.
A new command can be issued 2 clock cycles after EMRS or MRS.
3. Auto refresh functions are same as the CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by "Auto".
Auto/self refresh can be issued only at all banks precharge state.
4. BA0 ~ BA1 : Bank select addresses.
If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected.
If BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank B is selected.
If BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank C is selected.
If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected.
5. If A10/AP is "High" at row precharge, BA0 and BA1 are ignored and all banks are selected.
6. During burst write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
7. Burst stop command is valid at every burst length.
8. DM sampled at the rising and falling edges of the DQS and Data-in are masked at the both edges (Write DM latency is 0).
9. This combination is not defined for any function, which means "No Operation(NOP)" in DDR SDRAM.
相關PDF資料
PDF描述
M38220MCMFS 50000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
M38220E1FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38220E1FS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38220E1GP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38220MCHXXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M381L2923CUM-CB300 制造商:Samsung Semiconductor 功能描述:512MSDDDR_MDDR SDRAM MODULX72TSOP2-400(LF) - Bulk
M381L6423ETM-CA200 制造商:Samsung Semiconductor 功能描述:256 DDR SDRAM MODUL X72 TSOP2-400 - Trays
M3820 功能描述:電纜固定件和配件 LTRSCG 875 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M38203 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38203E4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER