- 您現在的位置：買賣IC網 > PDF目錄67763 > M37754FFCGP 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M37754FFCGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 24/68頁 |
| 文件大?。?/td> | 605K |
| 代理商： | M37754FFCGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
30
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
MITSUBISHI MICROCOMPUTERS
M37754FFCGP
M37754FFCHP
SHINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
Auto erase command
Input command code 3016 in the first transfer and command code
3016 again in the second transfer. When this is done, the
M37754FFCGP and the M37754FFCHP execute an auto erase
command. Auto erase is initiated at the last rising edge of the serial
clock. The BUSY pin is driven high during the auto erase operation.
Auto erase is completed when all memory contents are erased, and
the BUSY pin is pulled low.
Note: In the auto erase operation, the M37754FFCGP and the
M37754FFCHP automatically repeat the erase and verify op-
erations internally. Therefore, erase is completed by execut-
ing the command once.
Error check command
Input command code 8016 in the first transfer, and the
M37754FFCGP and the M37754FFCHP output error information
from the SDA pin, beginning at the next falling edge of the serial
clock. If the E0 of the 8-bit error information is 1, it indicates that a
command error has occurred. A command error means that some in-
valid commands other than commands shown in Table 4 has been
input.
When a command error occurs, the serial communication circuit sets
the corresponding flag and stops functioning to avoid an erroneous
programming or erase. When being placed in this state, the serial
communication circuit does not accept the subsequent serial clock
and data (even including an error check command). Therefore, if the
user wants to execute an error check command, temporarily drop
the VPP pin input to the VPPL level to terminate the serial input/out-
put mode. Then, place the M37754FFCGP and the M37754FFCHP
into the serial I/O mode back again. The serial communication circuit
is reset by this operation and is ready to accept commands. The er-
ror flag alone is not cleared by this operation, so the user can exam-
ine the serial communication circuit’s error conditions before reset.
This examination is done by the first execution of an error check
command after the reset. The error flag is cleared when the user has
executed the error check command. Because the error flag is unde-
fined immediately after power-on, always be sure to execute the er-
ror check command.
Fig. 20 Timings at error checking
Fig. 19 Timings at auto-erasing
SCLK
BUSY
OE
SDA
tCH
tEC
00001100
Command code input (3016) Command code input (3016)
Auto-erase
“H”
SCLK
BUSY
OE
SDA
E0
tCH
Command code input (8016)
Error flag output
00000001
??????
Note: When outputting the error flag, the SDA pin is switched for output at the first falling edge of the serial clock. The SDA pin is placed
in the floating state during the period of th(C-E) after the last rising edge of the serial clock (at the 8th bit).
?
“H”
“L”
相關PDF資料 |
PDF描述 |
|---|---|
| M37905F8CFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64 |
| M37905F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP64 |
| M37920F8CHP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| M37920F8CGP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| M38039MFL-XXXHP | 8-BIT, MROM, 16.8 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37754FFCHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37754M6C-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37754M6C-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37754M8C-XXXGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| M37754M8C-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。