- 您現在的位置：買賣IC網 > PDF目錄180183 > M37735S4LHP 16-BIT, 12 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37735S4LHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, 12 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 12 X 12 MM, 0.50 MM PITCH, FINE PITCH, PLASTIC, LQFP-80 |
| 文件頁數： | 7/37頁 |
| 文件大?。?/td> | 819K |
| 代理商： | M37735S4LHP |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
14
MITSUBISHI MICROCOMPUTERS
M37735S4LHP
16-BIT CMOS MICROCOMPUTER
New
product
As shown in Table 3,
1
output can be stopped with the signal
output disable selection bit = “1”. In this case, write “1” to the port P42
direction register.
Table 1 shows the relationship between the CNVss pin input level
and the processor mode.
Table 1. Relationship between CNVss pin input levels and processor
mode
CNVss
Mode
Description
Microprocessor mode upon
starting after reset.
Microprocessor
Vcc
00 088016
to
00 7FFF16
00 800016
to
03 FFFF16
04 000016
to
07 FFFF16
08 000016
to
0B FFFF16
0C 000016
to
0F FFFF16
___
Table 2. Relationship between access addresses and chip-select signals CS0 to CS4
Access address
Microprocessor mode
Chip-select
signal
Area
The latter half of bank 0016 except
internal memory area and banks
0116 to 0316.
Banks 0416 to 0716
Banks 0816 to 0B16
Banks 0C16 to 0F16
The first half of bank 0016 except
internal memory area
___
CS0
___
CS1
___
CS2
___
CS3
___
CS4
Table 3. Function of signal output disable selection bit CM6 (bit 6 of oscillation circuit control register 0)
Function
CM6 = “0”
CM6 = “1”
Processor mode
Pin
Note. Functions shown in Table 3 cannot be emulated with a debugger. For the oscillation circuit control register 0 and port function control
register, refer to Figures 64 and 11 in data sheet “M37735MHBXXXFP”, respectively.
___
RDE
, WEL, WEH are output when the
internal/external memory area is accessed.
After WIT/STP instruction is executed,
“H” is output.
Clock
1
is output independent of
1
output selection bit.
___
RDE
,
___
WEL
, WEH
___
RDE
1
Microprocessor mode
___
RDE
, WEL, WEH are output only when the
external memory area is accessed.
“L” is output after WIT/STP instruction is
executed
Standby state selection bit (bit 0 of port
function control register) must be set to “1”.
“H” or “L” is output. (Contents of P42 port
latch is output.)
Port P42 direction register must be set to
“1”.
相關PDF資料 |
PDF描述 |
|---|---|
| M37736EHLXXXHP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP100 |
| M37736MHBXXXGP | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP100 |
| M37P75C4P3 | 4 CONTACT(S), MALE, TWO PART BOARD CONNECTOR |
| M37S07K4P3 | 4 CONTACT(S), FEMALE, TWO PART BOARD CONNECTOR, SOCKET |
| MX37004PP3 | 4 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37735T-PAC | 制造商:Renesas Electronics Corporation 功能描述:DEV 7733 SIMPLE DEVELOPMENT TOOL PACKAGE - Bulk |
| M37736EHB | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37736EHBXXXGP |
| M37736EHBGS | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:PROM VERSION OF M37736MHBXXXGP |
| M37736EHBXXXGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37736MHBXXXGP(MICROCOMPUTERS) |
| M37736EHL | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37736MHLXXXHP(MICROCOMPUTERS) |
發布緊急采購，3分鐘左右您將得到回復。