- 您現在的位置：買賣IC網 > PDF目錄370847 > M37641M8 (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37641M8 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 44/149頁 |
| 文件大?。?/td> | 1997K |
| 代理商： | M37641M8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁
44
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
change.
Some parametric limits are subject to
USB Transmission
Endpoint 0 to Endpoint 4 have IN (transmit) FIFOs individually.
Each endpoint
’
s FIFO is configured in following way:
Endpoint 0: 16-byte
Endpoint 1: Mode 0: 512-byte
Mode 1: 1024-byte
Mode 2: 0-byte
Mode 3: 2048-byte
Mode 4: 768-byte
Mode 5: 880-byte
Endpoint 2: Mode 0: 32-byte
Mode 1: 128-byte
Endpoint 3: 16-byte
Endpoint 4: 16-byte
When Endpoint 1 or Endpoint 2 is used for data transmit, the IN
FIFO size can be selected. Endpoint 1 and Endpoint 2 have pro-
grammable IN-FIFOs size; 6 modes for Endpoint 1, and 2 modes
for Endpoint 2. Each mode can be selected by the USB endpoint
FIFO mode selection register (address 005F
16
).
When writing data to the USB Endpoint-x FIFO (addresses 0060
16
to 0064
16
) in the SFR area, the internal write pointer for the IN
FIFO is automatically increased by 1. When the AUTO_SET bit is
“
1
”
and if the stored data reaches to the max. packet value set in
USB Endpoint x IN max. packet size register (address 005B
16
),
the USB FCU sets the IN_PKT_RDY bit to
“
1
”
. When the
AUTO_SET bit is
“
0
”
, the IN_PKT_RDY bit will not be automati-
cally set to
“
1
”
; it must be set to
“
1
”
by software. (The AUTO_SET
bit function is not applicable to Endpoint 0.)
The USB FCU transmits the data when it receives the next IN to-
ken. The IN_PKT_RDY bit automatically goes to
“
0
”
when the data
transfer is complete.
G
Isochronous transfer
Endpoints 1 to 4 can be used in isochronous transfer mode. When
using isochronous transfer mode, the ISO/TOGGLE_INIT bit must
be set to
“
1
”
. When ISO_UPDATE =
“
1
”
and the corresponding
endpoint
’
s ISO/TOGGLE_INIT bit =
“
1
”
, the USB FCU delays the
rise of the IN_PKT_RDY bit until the next SOF signal transmis-
sion. In this way, the USB FCU can synchronize a transmit data to
the SOF signal.
G
Interrupt transfer mode
Endpoints 1 to 4 can be used in interrupt transfer mode. During a
regular interrupt transfer, an interrupt transaction is similar to the
bulk transfer. Therefore, there is no special setting required. When
IN-endpoint is used for a rate feedback interrupt transfer, INTPT
bit of the IN_CSR register must be set to
“
1
”
. Once the INTPT bit
is set, data toggling occurs every time a data packet is transmitted
to the host, regardless of the handshake packet availability or
type. The following steps show how to configure the IN-endpoint
for the rate feedback interrupt transfer.
1. Set a value which is larger than 1/2 of the USB Endpoint-x FIFO
size to the USB Endpoint x IN max. package size register.
2. Set INTPT bit to
“
1
”
.
3. Flush the old data in the FIFO.
4. Load interrupt status information and set IN_PKT_RDY bit to
“
1
”
.
5. Repeat steps 3 and 4.
In a real application, the function-side always has transfer data
when the function sends an endpoint in a rate feedback interrupt.
Accordingly, the USB FCU never returns a NAK against the host
IN token for the rate feedback interrupt. The USB FCU always
transmits data in the FIFO in response to an IN token, regardless
of IN_PKT_RDY.
When MAXP size
≤
(a half of IN FIFO size), the IN FIFO can store
two packets (called double buffer). At this time, the IN FIFO sta-
tus can be checked by monitoring the IN_PKT_RDY bit and the
TX_NOT_EPT flag. The TX_NOT_EPT flag is a read-only flag
which shows the FIFO state. When IN_PKY_RDY = 0 and
TX_NOT_EPT = 0, IN FIFO is empty. When IN_PKY_RDY = 0 and
TX_NOT_EPT = 1, IN FIFO has one packet.
In double buffer mode, as long as the IN FIFO is not filled with
double packets, IN_PKT_RDY will not be set to
“
1
”
, even if it is set
to
“
1
”
by software, but TX_NOT_EPT flag will be set to
“
1
”
. In
single buffer mode, if MAXP > (a half of IN FIFO), this condition
never occurs.
When IN_PKT_RDY =
“
1
”
and TX_NOT_EPT =
“
1
”
, IN FIFO holds
two packets in double buffer mode and one packet in single
packet mode. In single packet mode, when the IN_PKT_RDY bit is
set to
“
1
”
by software, the TX_NOT_EPT flag is set to
“
1
”
as well.
During double buffer mode, if you want to load two packets se-
quentially, you must set the IN_PKT_RDY bit to
“
1
”
each time a
packet is loaded.
相關PDF資料 |
PDF描述 |
|---|---|
| M37641F8FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641F8HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8-100FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37702M2-127FP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37641M8-100FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8E8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37641M8-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。