參數資料
型號: M37544G2GP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32
封裝: 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32
文件頁數: 21/68頁
文件大?。?/td> 738K
代理商: M37544G2GP
7544 Group
Rev.1.04
2004.06.08
page 28 of 66
REJ03B0012-0104Z
Fig. 30 Block diagram of UART serial I/O
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O mode selection bit of the serial I/O control
register to “0”.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
The transmit and receive shift registers each have a buffer, but the
two buffers have the same address in memory. Since the shift reg-
ister cannot be written to or read from directly, transmit data is
written to the transmit buffer register, and receive data is read
from the receive buffer register.
The transmit buffer register can also hold the next data to be
transmitted, and the receive buffer register can hold a character
while the next character is being received.
Fig. 31 Operation of UART serial I/O function
XIN
1/4
OE
PE FE
1/16
Data bus
Receive buffer register
Address 001816
Receive shift register
Receive buffer full flag (RBF)
Receive interrupt request (RI)
Baud rate generator
Frequency division ratio 1/(n+1)
Address 001C16
ST/SP/PA generator
Transmit buffer register
Data bus
Transmit shift register
Address 001816
Transmit shift completion flag (TSC)
Transmit buffer empty flag (TBE)
Transmit interrupt request (TI)
Address 001916
ST detector
SP detector
UART control register
Address 001B16
Character length selection bit
Address 001A16
BRG count source selection bit
Serial I/O synchronous clock selection bit
Clock control circuit
Character length selection bit
7 bits
8 bits
Serial I/O control register
P12/SCLK
Serial I/O status register
P10/RXD
P11/TXD
TSC=0
TBE=1
RBF=0
TBE=0
RBF=1
ST
D0
D1
SP
D0
D1
ST
SP
TBE=1
TSC=1
ST
D0
D1
SP
D0
D1
ST
SP
Transmit or receive clock
Transmit buffer write
signal
Generated at 2nd bit in 2-stop-bit mode
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1.”
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Notes
Serial output TXD
Serial input RXD
Receive buffer read
signal
相關PDF資料
PDF描述
M37549G2-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24
M37549G1-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24
M37549G1FP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24
M37560M8-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100
M37560EFDFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M37544G2HP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37544G2SP 功能描述:IC 740 MCU OTP 8K 32P4B RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 標準包裝:330 系列:- 核心處理器:- 芯體尺寸:8/16-位 速度:40MHz 連通性:UART/USART 外圍設備:DMA,PWM,WDT 輸入/輸出數:32 程序存儲器容量:- 程序存儲器類型:外部程序存儲器 EEPROM 大小:- RAM 容量:- 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-BQFP 包裝:管件
M37544M2-XXXGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37544M2-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37544M2-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER