- 您現在的位置：買賣IC網 > PDF目錄45035 > M37544G2ASP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 PDF資料下載
參數資料
| 型號： | M37544G2ASP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| 封裝： | 28 X 8.90 MM, 1.78 MM PITCH, PLASTIC, SDIP-32 |
| 文件頁數： | 38/77頁 |
| 文件大?。?/td> | 641K |
| 代理商： | M37544G2ASP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
7544 Group (QzROM version)
REJ03B0108-0103
Rev.1.03
Mar 31, 2009
page 41 of 72
(1) Oscillation control
Stop mode
When the STP instruction is executed, the internal clock φ stops at
an “H” level and the XIN oscillator stops. At this time, timer 1 is set
to “0116” and prescaler 1 is set to “FF16” when the oscillation sta-
bilization time set bit after release of the STP instruction is “0”. On
the other hand, timer 1 and prescaler 1 are not set when the
above bit is “1”. Accordingly, set the wait time fit for the oscillation
stabilization time of the oscillator to be used. Single selected by
the timer 1 count source selection bit is connected to the input of
prescaler 1. When an external interrupt is accepted, oscillation is
restarted but the internal clock φ remains at “H” until timer 1
underflows. As soon as timer 1 underflows, the internal clock φ is
supplied. This is because when a ceramic/quartz-crystal oscillator
is used, some time is required until a start of oscillation. In case
oscillation is restarted by reset, no wait time is generated. So ap-
______
ply an “L” level to the RESET pin while oscillation becomes stable.
Also, the STP instruction cannot be used while CPU is operating
by an on-chip oscillator.
Wait mode
If the WIT instruction is executed, the internal clock φ stops at an
“H” level, but the oscillator does not stop. The internal clock re-
starts if a reset occurs or when an interrupt is received. Since the
oscillator does not stop, normal operation can be started immedi-
ately after the clock is restarted. To ensure that interrupts will be
received to release the STP or WIT state, interrupt enable bits
must be set to “1” before the STP or WIT instruction is executed.
■ Notes on clock generating circuit
For use with the oscillation stabilization set bit after release of the
STP instruction set to “1”, set values in timer 1 and prescaler 1 af-
ter fully appreciating the oscillation stabilization time of the
oscillator to be used.
Switch of ceramic/quartz-crystal and RC oscillations
After releasing reset the operation starts by starting an on-chip os-
cillator. Then, a ceramic/quartz-crystal oscillation or an RC
oscillation is selected by setting bit 5 of the CPU mode register.
Double-speed mode
When a ceramic/quartz-crystal oscillation is selected, a double-
speed mode can be used. Do not use it when an RC oscillation is
selected.
CPU mode register
Bits 5, 1 and 0 of CPU mode register are used to select oscillation
mode and to control operation modes of the microcomputer. In or-
der to prevent the dead-lock by error-writing (ex. program
run-away), these bits can be rewritten only once after releasing re-
set. After rewriting it is disable to write any data to the bit. (The
emulator MCU “M37544RSS” is excluded.)
Also, when the read-modify-write instructions (SEB, CLB) are ex-
ecuted to bits 2 to 4, 6 and 7, bits 5, 1 and 0 are locked.
Clock division ratio, XIN oscillation control, on-chip oscillator con-
trol
The state transition shown in Fig. 49 can be performed by setting
the clock division ratio selection bits (bits 7 and 6), XIN oscillation
control bit (bit 4), on-chip oscillator oscillation control bit (bit 3) of
CPU mode register. Be careful of notes on use in Fig. 49.
Count source (Timer 1, Timer A, Timer X, Serial I/O, A/D con-
verter, Watchdog timer)
The count sources of these functions are affected by the clock di-
vision selection bit of the CPU mode register.
The f(XIN) clock is supplied to the watchdog timer when selecting
f(XIN) as the CPU clock.
The on-chip oscillator output is supplied to these functions when
selecting the on-chip oscillator output as the CPU clock.
Fig. 45 Structure of CPU mode register
Processor mode bits (Note 1)
b1 b0
0
0 Single-chip mode
0
1
0
1
Not available
b7
b0
2: These bits are used only when a ceramic/quartz-crystal oscillation is selected.
Note 1: The bit can be rewritten only once after releasing reset. After rewriting
it is disable to write any data to the bit. However, by reset the bit is
initialized and can be rewritten, again.
(It is not disable to write any data to the bit for emulator MCU
“M37544RSS”.)
Do not use these when an RC oscillation is selected.
Oscillation mode selection bit (Note 1)
0 : Ceramic/quartz-crystal oscillation
1 : RC oscillation
CPU mode register
(CPUM: address 003B16, initial value: 8016)
Stack page selection bit
0 : 0 page
1 : 1 page
Clock division ratio selection bits
b7 b6
0
0 : f(φ) = f(XIN)/2 (High-speed mode)
0
1 : f(φ) = f(XIN)/8 (Middle-speed mode)
1
0 : applied from on-chip oscillator
1
1 : f(φ) = f(XIN) (Double-speed mode)(Note 2)
On-chip oscillator oscillation control bit
0 : On-chip oscillator oscillation enabled
1 : On-chip oscillator oscillation stop
XIN oscillation control bit
0 : Ceramic/quartz-crystal or RC oscillation enabled
1 : Ceramic/quartz-crystal or RC oscillation stop
相關PDF資料 |
PDF描述 |
|---|---|
| M37544G2ASP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37544G2GP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37544G2SP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37545G2KP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO32 |
| M37545G8-XXXGP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37544G2ASP#U0 | 功能描述:MCU 2/5V 8K 32-SDIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M37544G2GP | 功能描述:IC 740 MCU OTP 8K 32LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| M37544G2HP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37544G2SP | 功能描述:IC 740 MCU OTP 8K 32P4B RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:330 系列:- 核心處理器:- 芯體尺寸:8/16-位 速度:40MHz 連通性:UART/USART 外圍設備:DMA，PWM，WDT 輸入/輸出數:32 程序存儲器容量:- 程序存儲器類型:外部程序存儲器 EEPROM 大小:- RAM 容量:- 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-BQFP 包裝:管件 |
| M37544M2-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。