參數資料
型號： M37542M2-XXXHP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36
封裝： 6 X 6 MM, 0.50 MM PITCH, PLASTIC, WQFN-36
文件頁數： 89/122頁
文件大?。?/td> 1311K
代理商： M37542M2-XXXHP
7542 Group
Rev.3.03
Jul 11, 2008
Page 69 of 117
REJ03B0006-0303
NOTES ON USE
Countermeasures against noise
1. Shortest wiring length
(1) Package
Select the smallest possible package to make the total wiring
length short.
<Reason>
The wiring length depends on a microcomputer package. Use of a
small package, for example QFP and not DIP, makes the total wir-
ing length short to reduce influence of noise.
(3) Wiring for clock input/output pins
Make the length of wiring which is connected to clock I/O pins as
short as possible.
Make the length of wiring (within 20 mm) across the grounding
lead of a capacitor which is connected to an oscillator and the
VSS pin of a microcomputer as short as possible.
Separate the VSS pattern only for oscillation from other VSS pat-
terns.
<Reason>
If noise enters clock I/O pins, clock waveforms may be deformed.
This may cause a program failure or program runaway. Also, if a
potential difference is caused by the noise between the VSS level
of a microcomputer and the VSS level of an oscillator, the correct
clock will not be input in the microcomputer.
(2) Wiring for RESET pin
Make the length of wiring which is connected to the RESET pin as
short as possible. Especially, connect a capacitor across the
RESET pin and the VSS pin with the shortest possible wiring
(within 20mm).
<Reason>
The width of a pulse input into the RESET pin is determined by the
timing necessary conditions. If noise having a shorter pulse width
than the standard is input to the RESET pin, the reset is released
before the internal state of the microcomputer is completely initial-
ized. This may cause a program runaway.
Fig. 89 Wiring for clock I/O pins
Fig. 87 Selection of packages
DIP
SDIP
SOP
QFP
Fig. 88 Wiring for the RESET pin
RESET
Reset
circuit
Noise
VSS
Reset
circuit
VSS
RESET
VSS
N.G.
O.K.
Noise
XIN
XOUT
VSS
XIN
XOUT
VSS
N.G.
O.K.
(4) Wiring to CNVss pin
Connect the CNVss pin to the Vss pin with the shortest possible
wiring.
In the normal microcomputer mode, disconnect a wiring of a serial
rewrite circuit, which is for the flash memory version, from the
MCU by a jumper switch.
<Reason>
The processor mode of a microcomputer is influenced by a poten-
tial at the CNVss pin. If a potential difference is caused by the
noise between pins CNVss and Vss, the processor mode may be-
come unstable. This may cause a microcomputer malfunction or a
program runaway.
A wiring of a serial rewrite circuit may function as an antenna
which feeds noise into the microcomputer.
Fig. 90 Wiring for CNVss pin
Noise
CNVSS
VSS
N.G.
CNVSS
VSS
O.K.
CNVSS
VSS
Jumper switch
Serial
rewrite
circuit
O.K.
Flash memory version
相關PDF資料
PDF描述
M37542M2-XXXGP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32
M37542F4SP 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32
M37542F8HP 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQCC36
M37544G2ASP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32
M37544G2ASP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32
相關代理商/技術參數
參數描述
M37542M2-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37542M4-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37542M4-XXXGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37542M4-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37542M4-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*