參數資料
型號: M37270MF-XXXSP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP64
封裝: 0.750 INCH, 1.78 MM PITCH, PLASTIC, SDIP-64
文件頁數: 14/97頁
文件大?。?/td> 1359K
代理商: M37270MF-XXXSP
MITSUBISHI MICROCOMPUTERS
M37270MF-XXXSP
M37270EF-XXXSP, M37270EFSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
18
Fig. 11. Structure of serial I/O mode register
Internal clock—the serial I/O counter is set to “7” during write cycle
into the serial I/O register (address 021416), and transfer clock goes
“H” forcibly. At each falling edge of the transfer clock after the write
cycle, serial data is output from the SOUT pin. Transfer direction can
be selected by bit 5 of the serial I/O mode register. At each rising
edge of the transfer clock, data is input from the SIN pin and data in
the serial I/O register is shifted 1 bit.
After the transfer clock has counted 8 times, the serial I/O counter
becomes “0” and the transfer clock stops at “H.” At this time the inter-
rupt request bit is set to “1.”
External clock—when an external clock is selected as the clock
source, the interrupt request is set to “1” after the transfer clock has
counted 8 times. However, transfer operation does not stop, so con-
trol the clock externally. Use the external clock of 500kHz or less
with a duty cycle of 50%.
The serial I/O timing is shown in Figure 10. When using an external
clock for transfer, the external clock must be held at “H” for initializing
the serial I/O counter. When switching between an internal clock and
an external clock, do not switch during transfer. Also, be sure to ini-
tialize the serial I/O counter after switching.
Notes 1: On programming, note that the serial I/O counter is set by
writing to the serial I/O register with the bit managing in-
structions as SEB and CLB instructions.
2: When an external clock is used as the synchronizing clock,
write transmit data to the serial I/O register at “H” of the
transfer clock input level.
Fig. 10. Serial I/O timing (for LSB first)
Synchroninzing clock
Transfer clock
Serial I/O register
write signal
Serial I/O output
SOUT
D0
D1
D2
D3
D4
D5
D6
D7
(Note)
Serial I/O input
SIN
Note : When an internal clock is selected, the SOUT pin is at high-impedance after transfer is completed.
Interrupt request bit is set to “1”
7
Serial I/O mode register
(SM : address 021316)
Internal synchronizing clock
selection bits
b1 b0
0
0 : f(XIN)/8 or f(XCIN)/8
0
1 : f(XIN)/16 or f(XCIN)/16
1
0 : f(XIN)/32 or f(XCIN)/32
1
1 : f(XIN)/64 or f(XCIN)/64
0
Synchronizing clock selection bit
0 : External clock
1 : Internal clock
Port function selection bit
0 : P11, P13 functions as port
1 : SCL1, SDA1
Port function selection bit
0 : P12, P14 functions as port
1 : SCL2, SDA2
Transfer direction selection bit
0 : LSB first
1 : MSB first
Fix these bits to “0”
0
相關PDF資料
PDF描述
M37272E8FP 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDSO42
M3727GM8-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42
M37272E8SP 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDIP42
M3727GM6-XXXFP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42
M37272M6-XXXFP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDSO42
相關代理商/技術參數
參數描述
M37271EF 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37271EFSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37271EFSS 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 類別:編程器,開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230,RCB231,RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
M37271EF-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M37271MF 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER