- 您現在的位置：買賣IC網 > PDF目錄359055 > M35080BN (意法半導體) 8 Kbit Serial SPI Bus EEPROM With Incremental Registers PDF資料下載
參數資料
| 型號： | M35080BN |
| 廠商： | 意法半導體 |
| 元件分類： | EEPROM |
| 英文描述： | 8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| 中文描述： | 8千位串行SPI總線的EEPROM與增量寄存器 |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 139K |
| 代理商： | M35080BN |
M35080
8/18
Figure 8. Write Enable Latch Sequence
C
D
AI01794
S
Q
2
1
3
4
5
6
7
HIGH IMPEDANCE
0
Figure 9. Byte Write Operation Sequence
Note: 1. The most significant address bits, A15-A10, are treated as Don’t Care.
C
D
AI01795
S
Q
15
2
1
3
4
5
6
7
8
9 10
20 21 22 23 24 25 26 27
14 13
3
2
1
0
28 29 30
HIGH IMPEDANCE
INSTRUCTION
16 BIT ADDRESS
0
7
6
5
4
3
2
0
1
DATA BYTE
31
as shown in Figure 9, otherwise the write process
is cancelled. As soon as the memory device is de-
selected, the self-timed internal write cycle is initi-
ated. While the write is in progress, the status
register may be read to check the status of the SR-
WD, BP1, BP0, WEL and WIP bits. In particular,
WIP contains a ‘1’ during the self-timed write cy-
cle, and a ‘0’ when the cycle is complete, (at which
point the write enable latch is also reset).
Write Data In the Incremental Registers
Due to the special control on the first page of the
memory, the byte write operation is not usable on
the first 32 bytes. Instead, the WRINC instruction
must be used, the timing of which is shown in Fig-
ure 10.
Prior to any write attempt, the write enable latch
must be set by issuing the WREN instruction. First
the device is selected (by taking S low) and a seri-
al WREN instruction is issued. Then the device is
deselected, by taking S high for at least t
SHSL
. The
device sets the write enable latch, and remains in
its stand-by state, until it is deselected. Then the
write state is entered by selecting the chip, by tak-
ing S low. The WRINC instruction is issued, and
the address is sent (always an even address, with
A0=0) along with two bytes of data. The Chip Se-
lect input (S) must remain low for the entire dura-
tion of the operation.
The device must be deselected just after the
eighth bit of the second data byte has been
latched in. Otherwise, the write process is can-
celled. As a further protection, the WRINC instruc-
tion is cancelled if its duration is not exactly equal
to 40 clock pulses.
As soon as the device is deselected, the self-timed
write cycle is initiated. While the write is in
progress, the status register may be read, to check
the values of the UV, INC, BP1, BP0, WEL and
相關PDF資料 |
PDF描述 |
|---|---|
| M35080-MN6T | 8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080-MN3T | 8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080-BN6T | 8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080-BN3T | 8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35101-W4 | Contactless Memory Chip 13.56 MHz, 2048-bit High Endurance EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M35080-BN3T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080-BN6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS |
| M35080MN | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
| M35080-MN3T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Kbit Serial SPI Bus EEPROM With Incremental Registers |
發布緊急采購，3分鐘左右您將得到回復。