- 您現在的位置：買賣IC網 > PDF目錄370838 > M34514M8 (Mitsubishi Electric Corporation) SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M34514M8 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片4位微機的CMOS |
| 文件頁數： | 38/106頁 |
| 文件大小： | 1304K |
| 代理商： | M34514M8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
38
4513/4514 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
change.
Some parametric limits are subject to
Table 13 Processing sequence of data transfer from master to slave
Master (transmission)
[Initial setting]
Setting the serial I/O mode register J1 and inter-
rupt control register V2 shown in Figure 24.
TJ1A and TV2A instructions
Setting the port received the reception enable
signal (S
RDY
) to the input mode.
(Port D
5
is used in this example)
SD instruction
* [Transmission enable state]
Storing transmission data to serial I/O register SI.
TSIAB instruction
1-byte data is serially transferred on this process. Subsequently, data
can be transferred continuously by repeating the process from *.
When an external clock is selected as a synchronous clock, the
clock is not controlled internally. Control the clock externally be-
cause serial transfer is performed as long as clock is externally
input. (Unlike an internal clock, an external clock is not stopped
when serial transfer is completed.) However, the SIOF flag is set to
“1” when the clock is counted 8 times after executing the SST in-
struction. Be sure to set the initial level of the external clock to “H.”
[Transmission]
Check port D
5
is “L” level.
SZD instruction
Serial transfer starts.
SST instruction
Check transmission completes.
SNZSI instruction
Wait (timing when continuously transferring)
Slave (reception)
[Initial setting]
Setting serial I/O mode register J1, and interrupt control register V2 shown in
Figure 24.
TJ1A and TV2A instructions
Setting the port received the reception enable signal (S
RDY
) and outputting “H”
level (reception impossible).
(Port D
5
is used in this example)
SD instruction
*[Reception enable state]
The SIOF flag is cleared to “0.”
SST instruction
“L” level (reception possible) is output from port D
5
.
RD instruction
[Reception]
Check reception completes.
SNZSI instruction
“H” level is output from port D
5
.
SD instruction
[Data processing]
相關PDF資料 |
PDF描述 |
|---|---|
| M34513 | Single Chip 4 Bits CMOS Microcomputer(4位單片機) |
| M34514 | Single Chip 4 Bits CMOS Microcomputer(4位單片機) |
| M34514M6-263FP | SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34551 | SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTER |
| M34551E8 | 4-BIT SINGLE-CHIP MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34514M8-756FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34514M8-759FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34514M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34518E8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34518E8SP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。