參數資料
型號： M34280M1-XXXGP
元件分類： 微控制器/微處理器
英文描述： 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20
封裝： 0.225 INCH, 0.65 MM PITCH, PLASTIC, SSOP-20
文件頁數： 2/48頁
文件大小： 605K
代理商： M34280M1-XXXGP
7
MITSUBISHI MICROCOMPUTERS
4280 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS
Fig. 5 Stack registers (SKs) structure
Fig. 6 Example of operation at subroutine call
SK0
SK1
SK2
SK3
(SP) = 0
(SP) = 1
(SP) = 2
(SP) = 3
Program counter (PC)
Executing RT
instruction
Executing BM
instruction
Stack pointer (SP) points “3” at reset or
returning from RAM back-up mode. It points “0”
by executing the first BM instruction, and the
contents of program counter is stored in SK0.
When the BM instruction is executed after four
stack registers are used ((SP) = 3), (SP) = 0
and the contents of SK0 is destroyed.
Returning to the BM instruction execution
address with the RT instruction, and the BM
instruction is equivalent to the NOP instruction.
(SP)
0
(SK0)
000116
(PC)
SUB1
Main program
000216 NOP
Address
000016 NOP
000116 BM SUB1
Subroutine
SUB1 :
NOP
RT
(PC)
(SK0)
(SP)
3
Note:
(5) Most significant ROM code reference enable flag (URS)
URS flag controls whether to refer to the contents of the most
significant 1 bit (bit 8) of ROM code when executing the TABP
p instruction. If URS flag is “0,” the contents of the most
significant 1 bit of ROM code is not referred even when
executing the TABP p instruction. However, if URS flag is “1,”
the contents of the most significant 1 bit of ROM code is set to
flag CY when executing the TABP p instruction (Figure 4).
URS flag is “0” after system is released from reset and returned
from RAM back-up mode. It can be set to “1” with the URSC
instruction, but cannot be cleared to “0.”
(6) Stack registers (SKs) and stack pointer (SP)
Stack registers (SKs) are used to temporarily store the contents
of program counter (PC) just before branching until returning
to the original routine when;
performing a subroutine call, or
executing the table reference instruction (TABP p).
Stack registers (SKs) are four identical registers, so that
subroutines can be nested up to 4 levels. However, one of
stack registers is used when executing a table reference
instruction. Accordingly, be careful not to over the stack. The
contents of registers SKs are destroyed when 4 levels are
exceeded.
The register SK nesting level is pointed automatically by 2-bit
stack pointer (SP).
Figure 5 shows the stack registers (SKs) structure.
Figure 6 shows the example of operation at subroutine call.
(7) Skip flag
Skip flag controls skip decision for the conditional skip
instructions and continuous described skip instructions.
Note : The 4280 Group just invalidates the next instruction
when a skip is performed. The contents of program
counter is not increased by 2. Accordingly, the number
of cycles does not change even if skip is not performed.
However, the cycle count becomes “1” if the TABP p,
RT, or RTS instruction is skipped.
相關PDF資料
PDF描述
M34280E1GP 4-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO20
M34501M2-XXXFP 4-BIT, MROM, 4.4 MHz, MICROCONTROLLER, PDSO20
M34501E4FP 4-BIT, OTPROM, 4.4 MHz, MICROCONTROLLER, PDSO20
M34501M2-XXXFP 4-BIT, MROM, MICROCONTROLLER, PDSO20
M34501E4FP 4-BIT, OTPROM, MICROCONTROLLER, PDSO20
相關代理商/技術參數
參數描述
M3428-100 制造商:MANHATTEN 功能描述:24AWG COMPUTER CABLE
M34282 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34282E2 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34282E2GP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34282M1 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*