- 您現在的位置：買賣IC網 > PDF目錄359039 > M29W160DB90ZA1T (意法半導體) 16 Mbit 2Mb x8 or 1Mb x16, Boot Block 3V Supply Flash Memory PDF資料下載
參數資料
| 型號： | M29W160DB90ZA1T |
| 廠商： | 意法半導體 |
| 英文描述： | 16 Mbit 2Mb x8 or 1Mb x16, Boot Block 3V Supply Flash Memory |
| 中文描述： | 16兆位的2Mb x8或1兆x16插槽，啟動塊3V電源快閃記憶體 |
| 文件頁數： | 5/40頁 |
| 文件大小： | 665K |
| 代理商： | M29W160DB90ZA1T |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
5/40
M29W160ET, M29W160EB
SUMMARY DESCRIPTION
The M29W160E is a 16 Mbit (2Mb x8 or 1Mb x16)
non-volatile memory that can be read, erased and
reprogrammed. These operations can be per-
formed using a single low voltage (2.7 to 3.6V)
supply. On power-up the memory defaults to its
Read mode where it can be read in the same way
as a ROM or EPROM.
The memory is divided into blocks that can be
erased independently so it is possible to preserve
valid data while old data is erased. Each block can
be protected independently to prevent accidental
Program or Erase commands from modifying the
memory. Program and Erase commands are writ-
ten to the Command Interface of the memory. An
on-chip Program/Erase Controller simplifies the
process of programming or erasing the memory by
taking care of all of the special operations that are
required to update the memory contents.
The end of a program or erase operation can be
detected and any error conditions identified. The
command set required to control the memory is
consistent with JEDEC standards.
The blocks in the memory are asymmetrically ar-
ranged, see Figures 5 and 6, Block Addresses.
The first or last 64 KBytes have been divided into
four additional blocks. The 16 KByte Boot Block
can be used for small initialization code to start the
microprocessor, the two 8 KByte Parameter
Blocks can be used for parameter storage and the
remaining 32K is a small Main Block where the ap-
plication may be stored.
Chip Enable, Output Enable and Write Enable sig-
nals control the bus operation of the memory.
They allow simple connection to most micropro-
cessors, often without additional logic.
The memory is offered TSOP48 (12 x 20mm) and
TFBGA48 (0.8mm pitch) packages. The memory
is supplied with all the bits erased (set to ’1’).
Figure 2. Logic Diagram
Table 1. Signal Names
AI06849B
20
A0-A19
W
DQ0-DQ14
VCC
M29W160ET
M29W160EB
E
VSS
15
G
RP
DQ15A–1
RB
BYTE
A0-A19
Address Inputs
DQ0-DQ7
Data Inputs/Outputs
DQ8-DQ14
Data Inputs/Outputs
DQ15A–1
Data Input/Output or Address Input
E
Chip Enable
G
Output Enable
W
Write Enable
RP
Reset/Block Temporary Unprotect
RB
Ready/Busy Output
BYTE
Byte/Word Organization Select
V
CC
Supply Voltage
V
SS
Ground
NC
Not Connected Internally
相關PDF資料 |
PDF描述 |
|---|---|
| M29W160DB90ZA6T | DUAL 2-INPUT EXCLUSIVE-OR GATE 8-DSBGA -40 to 85 |
| M29W160DT | 16 Mbit 2Mb x8 or 1Mb x16, Boot Block 3V Supply Flash Memory |
| M29W160DT70M1T | 16 Mbit 2Mb x8 or 1Mb x16, Boot Block 3V Supply Flash Memory |
| M29W160DT70M6T | Dual Inverter Gate 6-SC70 -40 to 85 |
| M29W160DT70N1T | Quadruple 2-Input Positive-OR Gate 14-VQFN -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M29W160DB90ZA6 | 功能描述:閃存 STD FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M29W160DB90ZA6E | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DB90ZA6F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DB90ZA6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。