- 您現在的位置：買賣IC網 > PDF目錄296349 > M29W160BT90ZA6 (NUMONYX) 1M X 16 FLASH 2.7V PROM, 90 ns, PBGA48 PDF資料下載
參數資料
| 型號： | M29W160BT90ZA6 |
| 廠商： | NUMONYX |
| 元件分類： | PROM |
| 英文描述： | 1M X 16 FLASH 2.7V PROM, 90 ns, PBGA48 |
| 封裝： | 0.80 MM PITCH, LFBGA-48 |
| 文件頁數： | 4/25頁 |
| 文件大小： | 171K |
| 代理商： | M29W160BT90ZA6 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁
M29W160BT, M29W160BB
12/25
STATUS REGISTER
Bus Read operations from any address always
read the Status Register during Program and
Erase operations. It is also read during Erase Sus-
pend when an address within a block being erased
is accessed.
The bits in the Status Register are summarized in
Table 11, Status Register Bits.
Data Polling Bit (DQ7). The Data Polling Bit can
be used to identify whether the Program/Erase
Controller has successfully completed its opera-
tion or if it has responded to an Erase Suspend.
The Data Polling Bit is output on DQ7 when the
Status Register is read.
During Program operations the Data Polling Bit
outputs the complement of the bit being pro-
grammed to DQ7. After successful completion of
the Program operation the memory returns to
Read mode and Bus Read operations from the ad-
dress just programmed output DQ7, not its com-
plement.
During Erase operations the Data Polling Bit out-
puts ’0’, the complement of the erased state of
DQ7. After successful completion of the Erase op-
eration the memory returns to Read Mode.
In Erase Suspend mode the Data Polling Bit will
output a ’1’ during a Bus Read operation within a
block being erased. The Data Polling Bit will
change from a ’0’ to a ’1’ when the Program/Erase
Controller has suspended the Erase operation.
Figure 5, Data Polling Flowchart, gives an exam-
ple of how to use the Data Polling Bit. A Valid Ad-
dress is the address being programmed or an
address within the block being erased.
Toggle Bit (DQ6). The Toggle Bit can be used to
identify whether the Program/Erase Controller has
successfully completed its operation or if it has re-
sponded to an Erase Suspend. The Toggle Bit is
output on DQ6 when the Status Register is read.
During Program and Erase operations the Toggle
Bit changes from ’0’ to ’1’ to ’0’, etc., with succes-
sive Bus Read operations at any address. After
successful completion of the operation the memo-
ry returns to Read mode.
During Erase Suspend mode the Toggle Bit will
output when addressing a cell within a block being
erased. The Toggle Bit will stop toggling when the
Program/Erase Controller has suspended the
Erase operation.
Figure 6, Data Toggle Flowchart, gives an exam-
ple of how to use the Data Toggle Bit.
Error Bit (DQ5). The Error Bit can be used to
identify errors detected by the Program/Erase
Controller. The Error Bit is set to ’1’ when a Pro-
gram, Block Erase or Chip Erase operation fails to
write the correct data to the memory. If the Error
Bit is set a Read/Reset command must be issued
before other commands are issued. The Error bit
is output on DQ5 when the Status Register is read.
Note that the Program command cannot change a
bit set at ’0’ back to ’1’ and attempting to do so may
or may not set DQ5 at ‘1’. In both cases, a succes-
sive Bus Read operation will show the bit is still ‘0’.
One of the Erase commands must be used to set
all the bits in a block or in the whole memory from
’0’ to ’1’.
Table 11. Status Register Bits
Note: Unspecified data bits should be ignored.
Operation
Address
DQ7
DQ6
DQ5
DQ3
DQ2
RB
Program
Any Address
DQ7
Toggle
0
–
0
Program During Erase
Suspend
Any Address
DQ7
Toggle
0
–
0
Program Error
Any Address
DQ7
Toggle
1
–
0
Chip Erase
Any Address
0
Toggle
0
1
Toggle
0
Block Erase before
timeout
Erasing Block
0
Toggle
0
Toggle
0
Non-Erasing Block
0
Toggle
0
No Toggle
0
Block Erase
Erasing Block
0
Toggle
0
1
Toggle
0
Non-Erasing Block
0
Toggle
0
1
No Toggle
0
Erase Suspend
Erasing Block
1
No Toggle
0
–
Toggle
1
Non-Erasing Block
Data read as normal
1
Erase Error
Good Block Address
0
Toggle
1
No Toggle
0
Faulty Block Address
0
Toggle
1
Toggle
0
相關PDF資料 |
PDF描述 |
|---|---|
| M29W400BT70M6T | 256K X 16 FLASH 2.7V PROM, 70 ns, PDSO44 |
| M29W640GB70ZA6F | 4M X 16 FLASH 3V PROM, 70 ns, PBGA48 |
| M2Y51264TU88A2G-37B | 64M X 64 DDR DRAM MODULE, 0.5 ns, DMA240 |
| M30-1201100 | 22 CONTACT(S), FEMALE, TWO PART BOARD CONNECTOR, CRIMP |
| M30-6000206R | 2 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M29W160BT90ZA6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8 or 1Mb x16, Boot Block Low Voltage Single Supply Flash Memory |
| M29W160DB | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8 or 1Mb x16, Boot Block 3V Supply Flash Memory |
| M29W160DB70M1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DB70M1E | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
| M29W160DB70M1F | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit (2Mb x8 or 1Mb x16, Boot Block) 3V Supply Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。