- 您現在的位置：買賣IC網 > PDF目錄369886 > LXT9860HC Controller Miscellaneous - Datasheet Reference PDF資料下載
參數資料
| 型號： | LXT9860HC |
| 英文描述： | Controller Miscellaneous - Datasheet Reference |
| 中文描述： | 控制器雜項-數據表參考 |
| 文件頁數： | 13/96頁 |
| 文件大?。?/td> | 1309K |
| 代理商： | LXT9860HC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
LXT980/980A Dual-Speed, 5-Port Fast Ethernet Repeater
Datasheet
13
Table 4. Inter-Repeater Backplane Signal Descriptions
Pin
Symbol
Type
1
Description
Common IRB Signals
199
MMSTRIN
TTL Input
PD, NC
Management Master Input.
The Management Master (MM) daisy chain ensures that
collisions are counted correctly in multi-board applications. Attach the MMSTRIN input
of each device to the MMSTROUT output of the previous device. Ground MMSTRIN of
the first or only device.
63
MMSTROUT
TTL Output
Management Master Output.
MM daisy chain output. In hot-swap applications, a
1 k
- 3 k
resistor can be used as a by-pass between MMSTRIN and MMSTROUT.
100 Mbps IRB Signals (Refer to Figure 22 on page 57)
36
IR100CFS
Analog I/O
100 Mbps IRB Collision Force Sense.
A
three-level signal that determines number of
active ports on the
“
logical
”
repeater. High level (5V) indicates no ports active; Mid level
(approx. 2.8V) indicates one port active; Low level (0V) indicates more than one port
active, resulting in a collision. This signal requires a 2
40
pull-up resistor, and connects
between chips on the same board.
37
IR100CFSBP
Analog I/O
NC
100 Mbps IRB Collision Force Sense - Backplane.
This three-level signal functions
the same as IRCFS; however, it connects between chips with ChipID=0, on different
boards. IR100CFSBP requires a single
91
pull-up resistor on each stack.
38
IR100SNGL
Schmitt
CMOS I/O
PU
100 Mbps Single Driver State.
This active Low signal is asserted by the device with
ChipID = 000 when a packet is being received from one or more ports. This signal
should not be connected between boards.
40
IR100COL
Schmitt
CMOS I/O
PU
100 Mbps Multiple Driver State.
This active Low signal is asserted by the device with
ChipID = 000 when a packet is being received from more than one port (collision). It
should not be connected between boards.
41
IR100DEN
TTL Output
OD
100 Mbps IRB Driver Enable.
This output provides directional control for an external
bidirectional transceiver (
‘
245) used to buffer the 100 Mbps IRB in multi-board
applications. It must be pulled up by a 330
resistor. When there are multiple devices
on one board, tie all IR100DEN outputs together. If IR100DEN is tied directly to the DIR
pin on a
‘
245, attach the on-board IR100DAT, IR100CLK, and IR100DV signals to the
“
B
”
side of the
‘
245, and connect the off-board signals to the
“
A
”
side of the
‘
245.
42
IR100DV
Schmitt
CMOS I/O
OD, PU
100 Mbps IRB Data Valid.
This active Low signal indicates port activity on the
repeater. IR100DV frames the clock and data of the packet on the backplane. This
signal requires a 120
pull-up resistor.
43
44
45
46
49
IR100DAT0
IR100DAT1
IR100DAT2
IR100DAT3
IR100DAT4
Tri-state
Schmitt
CMOS I/O
PU
100 Mbps IRB Data.
These bidirectional signals carry data on the 100 Mbps IRB. Data
is driven on the falling edge and sampled on the rising edge of IR100CLK. These
signals can be buffered between boards.
52
IR100CLK
Tri-state
Schmitt
CMOS I/O
PD
100 Mbps IRB Clock.
This bidirectional, non-continuous, 25 MHz clock is recovered
from received network traffic. Schmitt triggering is used to increase noise immunity. This
signal must be pulled to VCC when idle. One 1 k
pull-up resistor on both side of a
‘
245
buffer is recommended.
56
IR100ISO
TTL Output
100 Mbps Stack Backplane Isolate.
This output allows one LXT980 per Board the
ability to enable or disable an external bidirectional transceiver (
‘
245). Attach the output
to the Enable input of the
‘
245. The output is driven High (disable) to isolate the
100 Mbps IRB.
1. NC = No Clamp. Pad will not clamp input in the absence of power.
PU = Input contains pull-up.
PD = Input contains pull-down.
I/O = Input / Output.
OD = Open Drain
TTL = Transistor-Transistor Logic
Even if the IRB is not used, required pull-up resistors must be installed as listed above.
相關PDF資料 |
PDF描述 |
|---|---|
| LXT9863HC | LAN HUB CONTROLLER |
| LXT9880AGE | Controller Miscellaneous - Datasheet Reference |
| LXT9880AHC | Controller Miscellaneous - Datasheet Reference |
| LXT9880HC | Controller Miscellaneous - Datasheet Reference |
| LXT9883HC | LAN HUB CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT9863 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 10/100 Umnmanaged Repeater |
| LXT9863HC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN HUB CONTROLLER |
| LXT9880 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 10/100 Repeater with Intergrated Management |
| LXT9880AGE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| LXT9880AHC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
發布緊急采購，3分鐘左右您將得到回復。