- 您現在的位置：買賣IC網 > PDF目錄369886 > LXT917QC LAN Transceiver PDF資料下載
參數資料
| 型號： | LXT917QC |
| 英文描述： | LAN Transceiver |
| 中文描述： | 網絡收發器 |
| 文件頁數： | 11/42頁 |
| 文件大?。?/td> | 561K |
| 代理商： | LXT917QC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Flexible Quad Ethernet Repeater
—
LXT914
Datasheet
11
Table 4. LXT914 Serial Port Signal Descriptions (External Management Mode)
PLCC
PQFP
Symbol
I/O
Description
14
11
SENI
I
Serial Enable Input.
This active Low input is used to access the LXT914
serial interface. To write to the serial input (SDI), an External Management
Device (EMD) must drive this pin from High to Low. The input must be
asserted Low concurrent with the appearance of data on SDI and remain
Low for the duration of the serial input transaction.
15
12
SENO
O
Serial Enable Output.
This active Low output is used to access the serial
interface of an EMD. When the LXT914 sends a data stream to the EMD
through the serial port (SDO), this output transitions from High to Low and
remains Low for the duration of the serial transmission.
16
13
SDI
I
Serial Data Input.
This pin is the input for the EMD serial interface. Setup
and operating parameters are supplied to the LXT914 in a serial data
stream through this port when operating in the External Management
Mode.
17
14
SDO
I/O
Serial Data Output.
After each packet transmission or interrupt event, the
LXT914 reports status information to the EMD in a serial data stream
through this port.
18
16
SCLK
I
Serial Clock.
This 10 MHz clock synchronizes the serial interface between
the LXT914 and the EMD. Both devices must be supplied from the same
clock source. In synchronous mode, SCLK and BCLK may be tied together.
Table 5. LXT914 Serial Port Signal Descriptions (Local Management Mode)
PLCC
PQFP
Symbol
I/O
Description
14
11
CS
O
Chip Select.
The LXT914 is designed for use with an EEPROM or similar
device which may be used to store setup parameters and serially download
them to the LXT914 during initialization. In a single-device application or in
the first device of a daisy chain application, this pin is an active High Chip
Select output used to enable the EEPROM.
SENI
I
Serial Enable Input.
In subsequent devices of a daisy-chain configuration,
a High-to-Low transition on this pin enables the serial input port (SDI). The
input must be asserted concurrent with the appearance of data on SDI and
remain Low for the duration of the serial input transaction.
15
12
SENO
O
Serial Enable Output.
During initialization, the LXT914 accepts 48 bits of
setup data through the SDI port. After the 48th bit, the LXT914 asserts this
pin Low. When multiple LXT914 devices are connected in a daisy-chain,
this output is tied to the SENI input of the next device in the chain. Thus
each device in the chain is serially enabled by the previous device until all
the devices have read in their 48 bits of setup data.
16
13
SDI
I
Setup Data Input.
This pin is the serial input port for the setup parameters
(48 bits).This pin should be tied Low if no EEPROM is present.
17
14
RTS
I/O
Request To Send.
In a single-device application or in the first device of a
daisy chain application, this pin outputs a 9-bit, active High sequence. This
pin must be tied to the EEPROM DI input to trigger the EEPROM to
download its stored data. In subsequent devices this pin is not used.
18
16
SCLKIO
I/O
Serial Clock.
A 1 MHz clock provided by the first LXT914 in the chain to all
subsequent repeaters and the EEPROM. In the Local mode all repeaters
have their SCLKIO pins tied together.
相關PDF資料 |
PDF描述 |
|---|---|
| LXT9784BC | LAN TRANSCEIVER|OCTAL|BGA|324PIN|PLASTIC |
| LXT9784BE | LAN TRANSCEIVER|OCTAL|BGA|324PIN|PLASTIC |
| LXT9785BC | LAN TRANSCEIVER|OCTAL|BGA|241PIN|PLASTIC |
| LXT9785HC | LAN TRANSCEIVER|OCTAL|QFP|208PIN|PLASTIC |
| LXT970AQC | LAN TRANSCEIVER|SINGLE|CMOS|QFP|64PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT918 | 制造商:LVL1 制造商全稱:LVL1 功能描述:Multi-Segment Hub Repeater |
| LXT918QC | 制造商:LVL1 制造商全稱:LVL1 功能描述:Multi-Segment Hub Repeater |
| LXT944 | 制造商:LVL1 制造商全稱:LVL1 功能描述:Quad Ethernet Interface Adapter |
| LXT944QC | 制造商:LEVELONE 功能描述: |
| LXT970 | 制造商:LVL1 制造商全稱:LVL1 功能描述:Fast Ethernet Transceiver |
發布緊急采購，3分鐘左右您將得到回復。