- 您現在的位置：買賣IC網 > PDF目錄369885 > LXT361PE Telecommunication IC PDF資料下載
參數資料
| 型號： | LXT361PE |
| 英文描述： | Telecommunication IC |
| 中文描述： | 通信集成電路 |
| 文件頁數： | 13/52頁 |
| 文件大小： | 1187K |
| 代理商： | LXT361PE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Integrated T1/E1 LH/SH Transceiver for DS1/DSX-1 or PRI Applications
—
LXT361
Datasheet
13
3.0
Functional Description
The LXT361 is a fully integrated, PCM transceiver for Long- or Short-Hual, 1.544 Mbps (T1) or
2.048 Mbps (E1) applications allowing full-duplex transmission of digital data over existing
twisted-pair installations. The device interfaces with two twisted-pair lines (one pair each for
transmit and receive) through standard pulse transformers and appropriate resistors.
The figure on the front page of this data sheet shows a block diagram of the LXT361. Control of
the chip is via the 8-bit parallel microprocessor port. Stand-alone operation is not supported.
The LXT361 provides a high-precision, crystal-less Jitter Attenuator (JA). The user may place the
JA in the transmit or receive path, or bypass it completely.
The transceiver meets or exceeds FCC, ANSI, and AT&T specifications for CSU and DSX-1
applications, as well as ITU and ETSI requirements for E1 ISDN PRI applications.
3.1
Initialization
During power up, the transceiver remains static until the power supply reaches approximately 3 V.
Upon crossing this threshold, the device begins a 32 ms reset cycle to calibrate the Phase Lock
Loops (PLL). The transceiver uses a reference clock to calibrate the PLLs: the transmitter reference
is TCLK, and the receiver reference clock is MCLK. MCLK is mandatory for chip operation and
must be independent, free running, and jitter free.
3.1.1
Reset Operation
A reset operation initializes the status and state machines for the LOS, AIS, NLOOP, and QRSS
blocks. Writing a 1 to the bit CR2.RESET commands a reset which clears all registers to 0. Allow
32 ms for the device to settle.
3.2
Transmitter
3.2.1
Transmit Digital Data Interface
Input data for transmission onto the line is clocked serially into the device at the TCLK rate. TPOS
and TNEG are the bipolar data inputs. In Unipolar mode, the TDATA pin accepts unipolar data.
Input data may pass through either the Jitter Attenuator or B8ZS/HDB3 encoder or both. Setting
CR1.ENCENB = 1 enables B8ZS/HDB3 encoding. With zero suppression enabled, Control
Register #1 (CR1) bits EC1 through EC4 determine the coding scheme as listed in
Table 8 on
page 27
.
TCLK supplies input synchronization. See the
Figure 14 on page 41
for the transmit timing
requirements for TCLK and the Master Clock (MCLK).
相關PDF資料 |
PDF描述 |
|---|---|
| LXT362LE | PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC |
| LXT362PE | PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|LDCC|28PIN|PLASTIC |
| LXT362QE | PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC |
| LXT363LE | PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC |
| LXT363PE | PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|LDCC|28PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT361QE | 制造商:LEVEL ONE 功能描述: 制造商:LEVEL ONE 功能描述:DATACOM, PCM TRANSCEIVER, PQFP44 |
| LXT362 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Integrated T1 LH/SH Transceiver for DS1/DSX-1 or PRI Applications |
| LXT362LE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC |
| LXT362PE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|LDCC|28PIN|PLASTIC |
| LXT362QE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。