- 您現在的位置：買賣IC網 > PDF目錄377786 > LTNN (Linear Technology Corporation) 24-Bit No Latency ADC with Differential Input and Reference in MSOP PDF資料下載
參數資料
| 型號： | LTNN |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 24-Bit No Latency ADC with Differential Input and Reference in MSOP |
| 中文描述： | 24位不具有差動輸入和ADC的參考延遲，采用MSOP |
| 文件頁數： | 14/40頁 |
| 文件大?。?/td> | 503K |
| 代理商： | LTNN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
LTC2411/LTC2411-1
14
As long as the voltage on the IN
+
and IN
–
pins is maintained
within the –0.3V to (V
CC
+ 0.3V) absolute maximum
operating range, a conversion result is generated for any
differential input voltage V
IN
from –FS = –0.5 V
REF
to
+FS = 0.5 V
REF
. For differential input voltages greater than
+FS, the conversion result is clamped to the value corre-
sponding to the +FS + 1LSB. For differential input voltages
below –FS, the conversion result is clamped to the value
corresponding to –FS – 1LSB.
Frequency Rejection Selection (F
O
) (LTC2411 Only)
The LTC2411 internal oscillator provides better than 110dB
normal mode rejection at the line frequency and all its
harmonics for 50Hz
±
2% or 60Hz
±
2%. For 60Hz rejec-
tion, F
O
should be connected to GND while for 50Hz
rejection the F
O
pin should be connected to V
CC
.
The selection of 50Hz or 60Hz rejection can also be made
by driving F
O
to an appropriate logic level. A selection
change during the sleep or data output states will not
disturb the converter operation. If the selection is made
during the conversion state, the result of the conversion in
progress may be outside specifications but the following
conversions will not be affected.
When a fundamental rejection frequency different from
50Hz or 60Hz is required or when the converter must be
synchronized with an outside source, the LTC2411 can
operate with an external conversion clock. The converter
automatically detects the presence of an external clock
signal at the F
O
pin and turns off the internal oscillator. The
frequency f
EOSC
of the external signal must be at least
2560Hz (1Hz notch frequency) to be detected. The exter-
nal clock signal duty cycle is not significant as long as the
minimum and maximum specifications for the high and
low periods t
HEO
and t
LEO
are observed.
While operating with an external conversion clock of a
frequency f
EOSC
, the LTC2411 provides better than 110dB
normal mode rejection in a frequency range f
EOSC
/2560
±
4% and its harmonics. The normal mode rejection as a
function of the input frequency deviation from f
EOSC
/2560
is shown in Figure 4.
Whenever an external clock is not present at the F
O
pin, the
converter automatically activates its internal oscillator and
enters the Internal Conversion Clock mode. The LTC2411
operation will not be disturbed if the change of conversion
clock source occurs during the sleep state or during the
data output state while the converter uses an external
serial clock. If the change occurs during the conversion
state, the result of the conversion in progress may be
outside specifications but the following conversions will
not be affected. If the change occurs during the data output
state and the converter is in the Internal SCK mode, the
serial clock duty cycle may be affected but the serial data
stream will remain valid.
Table 3 summarizes the duration of each state and the
achievable output data rate as a function of F
O
.
Simultaneous Frequency Rejection (LTC2411-1 Only)
The LTC2411-1 internal oscillator provides better than
87dB normal mode rejection over the range of 49Hz to
61.2Hz. For this simultaneous 50/60Hz rejection, F
O
should
be connected to GND. The performance of the LTC2411-1
is the same as the LTC2411 when driven by an external
conversion clock at F
O
pin.
SERIAL INTERFACE PINS
The LTC2411/LTC2411-1 transmit the conversion results
and receive the start of conversion command through a
synchronous 3-wire interface. During the conversion and
sleep states, this interface can be used to assess the
Figure 4. LTC2411 Normal Mode Rejection When
Using an External Oscillator of Frequency f
EOSC
DIFFERENTIAL INPUT SIGNAL FREQUENCY
DEVIATION FROM NOTCH FREQUENCY f
EOSC
/2560(%)
–12
–8
–4
0
4
8
12
N
2411 F04
–80
–85
–90
–95
–100
–105
–110
–115
–120
–125
–130
–135
–140
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2411-1CMS | 24-Bit No Latency ADC with Differential Input and Reference in MSOP |
| LTC2411-1IMS | 24-Bit No Latency ADC with Differential Input and Reference in MSOP |
| LTNS | 24-Bit No Latency ADC with Differential Input and Reference in MSOP |
| LTNT | 24-Bit No Latency ADC with Differential Input and Reference in MSOP |
| LTWV | 24-Bit No Latency ADC with Differential Input and Reference in MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTNS | 制造商:LINER 制造商全稱:Linear Technology 功能描述:24-Bit No Latency ADC with Differential Input and Reference in MSOP |
| LTNT | 制造商:LINER 制造商全稱:Linear Technology 功能描述:24-Bit No Latency ADC with Differential Input and Reference in MSOP |
| LTO-01T-110N | 制造商:JST Manufacturing 功能描述:Crimping Tools, Hand Tools 制造商:Pentair Technical Products / Hoffman 功能描述:TERMINAL FEMALE DISCONNECT 0.11IN CRIMP 制造商:HOFFMAN PRODUCTS 功能描述:TERMINAL, FEMALE DISCONNECT 0.11IN CRIMP 制造商:Pentair Technical Products / Hoffman 功能描述:TERMINAL, FEMALE DISCONNECT 0.11IN CRIMP; Connector Type:Female Disconnect; Series:-; Termination Method:Crimp; Stud/Tab Size:0.11" x 0.02"; Wire Size AWG Min:24AWG; Wire Size AWG Max:20AWG; Insulator Material:Uninsulated |
| LTO-01T-187N | 制造商:JST Manufacturing 功能描述: |
| LTO030F10000FTE3 | 功能描述:厚膜電阻器 - 透孔 1K OHM 1% 30W RoHS:否 制造商:Caddock 電阻:27 kOhms 容差:1 % 功率額定值:8 W 溫度系數:50 PPM / C 系列:MS 端接類型:Axial 電壓額定值:2 kV 工作溫度范圍:- 15 C to + 275 C 尺寸:8.89 mm Dia. x 23.11 mm L 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。