- 您現在的位置：買賣IC網 > PDF目錄10343 > LTC2480HDD#PBF (Linear Technology)IC ADC 16BIT SRL 7.5SPS 10DFN PDF資料下載
參數資料
| 型號： | LTC2480HDD#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 20/42頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT SRL 7.5SPS 10DFN |
| 標準包裝： | 121 |
| 位數： | 16 |
| 采樣率（每秒）： | 7.5 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 10-DFN（3x3） |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，雙極；1 個差分，雙極 |
| 配用： | DC798B-ND - BOARD DELTA SIGMA ADC LTC2480 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LTC2480
2480fd
Digital Signal Levels
The LTC2480’s digital interface is easy to use. Its digital
inputs (SDI, fO, CS and SCK in External SCK mode of
operation) accept standard CMOS logic levels and the
internal hysteresis receivers can tolerate edge transition
times as slow as 100s. However, some considerations
are required to take advantage of the exceptional accuracy
and low supply current of this converter.
The digital output signals (SDO and SCK in Internal SCK
mode of operation) are less of a concern because they are
not generally active during the conversion state.
While a digital input signal is in the range 0.5V to
(VCC – 0.5V), the CMOS input receiver draws additional
current from the power supply. It should be noted that,
when any one of the digital input signals (SDI, fO, CS and
SCKinExternalSCKmodeofoperation)iswithinthisrange,
the power supply current may increase even if the signal in
questionisatavalidlogiclevel.Formicropoweroperation,
it is recommended to drive all digital input signals to full
CMOS levels [VIL < 0.4V and VOH > (VCC – 0.4V)].
During the conversion period, the undershoot and/or
overshoot of a fast digital signal connected to the pins can
severely disturb the analog to digital conversion process.
Undershoot and overshoot occur because of the imped-
ance mismatch of the circuit board trace at the converter
pin when the transition time of an external control signal
is less than twice the propagation delay from the driver
to the LTC2480. For reference, on a regular FR-4 board,
signal propagation velocity is approximately 183ps/inch
for internal traces and 170ps/inch for surface traces.
Thus, a driver generating a control signal with a minimum
transition time of 1ns must be connected to the converter
pin through a trace shorter than 2.5 inches. This problem
becomesparticularlydifficultwhensharedcontrollinesare
used and multiple reflections may occur. The solution is
to carefully terminate all transmission lines close to their
characteristic impedance.
Parallel termination near the LTC2480 pin will eliminate
this problem but will increase the driver power dissipa-
tion. A series resistor between 27Ω and 56Ω placed near
the driver output pin will also eliminate this problem
without additional power dissipation. The actual resistor
value depends upon the trace impedance and connection
topology.
Analternatesolutionistoreducetheedgerateofthecontrol
signals. It should be noted that using very slow edges will
increase the converter power supply current during the
transition time. The differential input architecture reduces
the converter’s sensitivity to ground currents.
Particular attention must be given to the connection of
the fO signal when the LTC2480 is used with an external
conversion clock. This clock is active during the conver-
sion time and the normal mode rejection provided by the
internal digital filter is not very high at this frequency. A
normal mode signal of this frequency at the converter
reference terminals can result in DC gain and INL errors.
A normal mode signal of this frequency at the converter
input terminals can result in a DC offset error. Such pertur-
bations can occur due to asymmetric capacitive coupling
between the fO signal trace and the converter input and/or
reference connection traces. An immediate solution is to
maintain maximum possible separation between the fO
signal trace and the input/reference signals. When the fO
signal is parallel terminated near the converter, substantial
AC current is flowing in the loop formed by the fO con-
nection trace, the termination and the ground return path.
Thus,perturbationsignalsmaybeinductivelycoupledinto
the converter input and/or reference. In this situation, the
user must reduce to a minimum the loop area for the fO
signal as well as the loop area for the differential input
and reference connections. Even when fO is not driven,
other nearby signals pose similar EMI threats which will
be minimized by following good layout practices.
applicaTions inForMaTion
相關PDF資料 |
PDF描述 |
|---|---|
| MS27497E10F98P | CONN RCPT 6POS WALL MNT W/PINS |
| 6282-6PG-321 | CONN PLUG 6POS CABLE PIN |
| SL403FX | CONN PLUG 3POS FEMALE W/COUPLING |
| MS27473E14B5PD | CONN PLUG 5POS STRAIGHT W/PINS |
| MS27508E22F35AA | CONN HSG RCPT 100POS BOX MT PIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2480HMS#PBF | 功能描述:IC ADC 16BIT SER/SPI 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| LTC2480HMS#TRPBF | 功能描述:IC ADC DELTA SIGMA 16BIT 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2480IDD | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 7.5sps 16-bit Serial 10-Pin DFN EP |
| LTC2480IDD#PBF | 功能描述:IC ADC 16BIT 10-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2480IDD#TR | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 7.5sps 16-bit Serial 10-Pin DFN EP T/R |
發布緊急采購，3分鐘左右您將得到回復。