- 您現在的位置：買賣IC網 > PDF目錄2006 > LTC2453ITS8#TRMPBF (Linear Technology)IC ADC 16BIT DELTA SIG TSOT23-8 PDF資料下載
參數資料
| 型號： | LTC2453ITS8#TRMPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 17/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT DELTA SIG TSOT23-8 |
| 產品培訓模塊： | LTC2460 and LTC2450 Delta Sigma ADC Families |
| 標準包裝： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 60 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 4mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-8 薄型，TSOT-23-8 |
| 供應商設備封裝： | TSOT-23-8 |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 1 個差分，雙極 |
| 產品目錄頁面： | 1348 (CN2011-ZH PDF) |
| 其它名稱： | LTC2453ITS8#TRMPBFDKR |
LTC2453
8
2453fc
Reference Voltage Range
Thisconverteracceptsatrulydifferentialexternalreference
voltage. The absolute/common mode voltage range for
REF+ and REF– pins covers the entire operating range of
the device (GND to VCC). For correct converter operation,
VREF+ must be >(2.5V + VREF–).
The LTC2453 differential reference input range is 2.5V to
VCC. For the simplest operation, REF+ can be shorted to
VCC and REF– can be shorted to GND.
Input Voltage Range
For most applications, VREF– ≤ (VIN+, VIN–) ≤ VREF+. Under
these conditions the output code is given (see Data Format
section) as 32768 (VIN+ – VIN–)/(VREF+ – VREF–) + 32768.
The output of the LTC2453 is clamped at a minimum value
of 0 and clamped at a maximum value of 65535.
The LTC2453 includes a proprietary system that can,
typically, correctly digitize each input 8LSB above
VREF+ and below VREF–, if the LTC2453’s output is not
clamped. As an example (Figure 2), if the user desires to
measure a signal slightly below ground, the user could
set VIN– = VREF– = GND, and VREF+ = 5V. If VIN+ = GND,
the output code would be approximately 32768. If VIN+
= GND – 8LSB = –1.22 mV, the output code would be
approximately 32760.
The total amount of overrange and underrange capability
is typically 31LSB for a given device. The 31LSB total
is distributed between the overrange and underrange
capability. For example, if the underrange capability is
8LSB,theoverrangecapabilityistypically31–8=23LSB.
I2C INTERFACE
The LTC2453 communicates through an I2C interface. The
I2C interface is a 2-wire open-drain interface supporting
multiple devices and masters on a single bus. The con-
nected devices can only pull the data line (SDA) LOW and
never drive it HIGH. SDA must be externally connected to
the supply through a pull-up resistor. When the data line
is free, it is HIGH. Data on the I2C bus can be transferred
at rates up to 100kbits/s in the Standard-Mode and up to
400kbits/s in the Fast-Mode. The VCC power should not
be removed from the device when the I2C bus is active to
avoid loading the I2C bus lines through the internal ESD
protection diodes.
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate either as
a transmitter or receiver, depending on the function of
the device. In addition to transmitters and receivers,
devices can also be considered as masters or slaves when
performing data transfers. A master is the device which
initiates a data transfer on the bus and generates the
clock signals to permit that transfer. Devices addressed
by the master are considered a slave. The address of the
LTC2453 is 0010100.
The LTC2453 can only be addressed as a slave. It can only
transmit the last conversion result. The serial clock line,
SCL, is always an input to the LTC2453 and the serial data
line SDA is bidirectional. Figure 3 shows the definition of
the I2C timing.
The START and STOP Conditions
A START (S) condition is generated by transitioning SDA
from HIGH to LOW while SCL is HIGH. The bus is consid-
ered to be busy after the START condition. When the data
transfer is finished, a STOP (P) condition is generated by
transitioning SDA from LOW to HIGH while SCL is HIGH.
The bus is free after a STOP is generated. START and STOP
conditions are always generated by the master.
When the bus is in use, it stays busy if a repeated START
(Sr)isgeneratedinsteadofaSTOPcondition.Therepeated
VIN+/VREF+
–0.001
OUTPUT
CODE
32772
32780
32788
0.001
2453 F02
32764
32756
32768
32776
32784
32760
32752
32748
–0.005
0
0.005
0.0015
SIGNALS
BELOW
GND
Figure 2. Output Code vs VIN+ with VIN– = 0 and VREF– = 0
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2482IDD#TRPBF | IC ADC 16BIT 10-DFN |
| LTC2483IDD#TRPBF | IC ADC 16BIT I2C 10-DFN |
| LTC2485CDD#TRPBF | IC ADC 24BIT I2C 10-DFN |
| LTC2487CDE#PBF | IC ADC 16BIT DELTA SIG 14-DFN |
| LTC2492IDE#TRPBF | IC ADC 24BIT DELTA SIG 14-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2460CDD#PBF | 功能描述:IC ADC 16BIT DELTA SIG 12-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2460CDD#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 12-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2460CMS#PBF | 功能描述:IC ADC 16BIT DELTA SIG 12-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2460CMS#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 12-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2460IDD#PBF | 功能描述:IC ADC 16BIT DELTA SIG 12-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。