- 您現在的位置：買賣IC網 > PDF目錄377770 > LTC2420 (Linear Technology Corporation) Micropower 20-bit ADC(微功耗，20位串行模數轉換器) PDF資料下載
參數資料
| 型號： | LTC2420 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Micropower 20-bit ADC(微功耗，20位串行模數轉換器) |
| 中文描述： | 微功耗20位ADC（微功耗，20位串行模數轉換器） |
| 文件頁數： | 18/36頁 |
| 文件大小： | 388K |
| 代理商： | LTC2420 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
18
LTC2420
into an internal static shift register. The device remains in
the sleep state until the first rising edge of SCK. Data is
shifted out the SDO pin on each falling edge of SCK
enabling external circuitry to latch data on the rising edge
of SCK. EOC can be latched on the first rising edge of SCK.
On the 24th falling edge of SCK, SDO goes HIGH (EOC = 1)
indicating a new conversion has begun.
Internal Serial Clock, Single Cycle Operation
This timing mode uses an internal serial clock to shift out
the conversion result and a CS signal to monitor and
control the state of the conversion cycle, see Figure 9.
In order to select the internal serial clock timing mode, the
serial clock pin (SCK) must be floating (Hi-Z) or pulled
HIGH prior to the falling edge of CS. The device will not
enter the internal serial clock mode if SCK is driven LOW
on the falling edge of CS. An internal weak pull-up resistor
is active on the SCK pin during the falling edge of CS;
therefore, the internal serial clock timing mode is auto-
matically selected if SCK is not externally driven.
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
Once CS is pulled LOW, SCK goes LOW and EOC is output
to the SDO pin. EOC = 1 while a conversion is in progress
and EOC = 0 if the device is in the sleep state.
When testing EOC, if the conversion is complete (EOC = 0),
the device will exit the sleep state and enter the data output
state if CS remains LOW. In order to prevent the device
from exiting the low power sleep state, CS must be pulled
HIGH before the first rising edge of SCK. In the internal
SCK timing mode, SCK goes HIGH and the device begins
outputting data at time t
EOCtest
after the falling edge of CS
(if EOC = 0) or t
EOCtest
after EOC goes LOW (if CS is LOW
during the falling edge of EOC). The value of t
EOCtest
is 23
μ
s
if the device is using its internal oscillator (F
0
= logic LOW
or HIGH). If F
O
is driven by an external oscillator of
frequency f
EOSC
, then t
EOCtest
is 3.6/f
EOSC
. If CS is pulled
HIGH before time t
EOCtest
, the device remains in the sleep
state. The conversion result is held in the internal static
shift register.
If CS remains LOW longer than t
EOCtest
, the first rising
edge of SCK will occur and the conversion result is serially
shifted out of the SDO pin. The data output cycle begins on
this first rising edge of SCK and concludes after the 24th
rising edge. Data is shifted out the SDO pin on each falling
edge of SCK. The internally generated serial clock is output
to the SCK pin. This signal may be used to shift the
SDO
SCK
(INTERNAL)
CS
MSB
EXR
SIG
BIT 0
LSB
20
BIT 4
TEST EOC
BIT 19
BIT 18
BIT 20
BIT 21
BIT 22
EOC
BIT 23
SLEEP
DATA OUTPUT
CONVERSION
CONVERSION
2420 F09
<t
EOCtest
V
CC
F
O
V
REF
SCK
V
IN
SDO
GND
CS
V
REF
0.1V TO V
CC
V
IN
–0.12V
REF
TO 1.12V
REF
1
μ
F
2.7V TO 5.5V
LTC2420
V
CC
10k
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
Hi-Z
Hi-Z
Hi-Z
Hi-Z
V
CC
TEST EOC
Figure 9. Internal Serial Clock, Single Cycle Operation
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2435IGN | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
| LTC2435-1IGN | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
| LTC2435 | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
| LTC2435-1 | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
| LTC2435-1CGN | 20-Bit No Latency ADCs with Differential Input and Differential Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2420CS8 | 功能描述:IC ADC 20BIT MICRPWR W/OSC 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2420CS8#PBF | 功能描述:IC ADC 20BIT MICRPWR W/OSC 8SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2420CS8#PBF | 制造商:Linear Technology 功能描述:A/D Converter (A-D) IC |
| LTC2420CS8#TR | 功能描述:IC A/D CONV 20BIT MICRPWR 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2420CS8#TRPBF | 功能描述:IC ADC 20BIT MICRPWR W/OSC 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。