- 您現在的位置：買賣IC網 > PDF目錄39416 > LTC2274IUJ (LINEAR TECHNOLOGY CORP) 1-CH 16-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PQCC40 PDF資料下載
參數資料
| 型號： | LTC2274IUJ |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 1-CH 16-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PQCC40 |
| 封裝： | 6 X 6 MM, PLASTIC, QFN-40 |
| 文件頁數： | 13/40頁 |
| 文件大?。?/td> | 897K |
| 代理商： | LTC2274IUJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
LTC2274
20
2274fb
APPLICATIONS INFORMATION
Direct Coupled Circuits
Figure 5 demonstrates the use of a differential amplier to
convert a single ended input signal into a differential input
signal. The advantage of this method is that it provides
low frequency input response; however, the limited gain
bandwidth of any op amp or closed-loop amplier will de-
grade the ADC SFDR at high input frequencies. Additionally,
wideband op amps or differential ampliers tend to have
high noise. As a result, the SNR will be degraded unless
the noise bandwidth is limited prior to the ADC input.
Reference Operation
Figure 6 shows the LTC2274 reference circuitry consisting
of a 2.5V bandgap reference, a programmable gain ampli-
er and control circuit. The LTC2274 has three modes of
reference operation: Internal Reference, 1.25V external
reference or 2.5V external reference. To use the internal
reference, tie the SENSE pin to VDD. To use an external
reference, simply apply either a 1.25V or 2.5V reference
voltage to the SENSE input pin. Both 1.25V and 2.5V applied
to SENSE will result in a full scale range of 2.25VP-P (PGA
= 0). A 1.25V output VCM is provided for a common mode
bias for input drive circuitry. An external bypass capacitor is
required for the VCM output. This provides a high frequency
low impedance path to ground for internal and external
circuitry. This is also the compensation capacitor for the
reference; it will not be stable without this capacitor. The
minimum value required for stability is 2.2μF.
The internal programmable gain amplier provides the
internal reference voltage for the ADC. This amplier has
very stringent settling requirements and is not accessible
for external use.
The SENSE pin can be driven ±5% around the nominal 2.5V
or 1.25V external reference inputs. This adjustment range
can be used to trim the ADC gain error or other system
gain errors. When selecting the internal reference, the
SENSE pin should be tied to VDD as close to the converter
as possible. If the sense pin is driven externally it should
be bypassed to ground as close to the device as possible
with 1μF (or larger) ceramic capacitor.
PGA Pin
The PGA pin selects between two gain settings for
the ADC front-end. PGA = 0 selects an input range of
2.25VP-P; PGA = 1 selects an input range of 1.5VP-P. The
2.25V input range has the best SNR; however, the distor-
tion will be higher for input frequencies above 100MHz.
For applications with high input frequencies, the low
input range will have improved distortion; however, the
SNR will be 2.4dB worse. See the Typical Performance
Characteristics section of this datasheet.
Figure 5. DC Coupled Input with Differential Amplier
–
+
AIN
+
AIN
–
2.2μF
12pF
VCM
LTC2274
ANALOG
INPUT
2274 F05
CM
AMPLIFIER = LTC6600-20,
LTC1993, ETC.
HIGH SPEED
DIFFERENTIAL
AMPLIFIER
25Ω
1x OR 2x
1.25V
SENSE
VCM
BUFFER
INTERNAL
ADC
REFERENCE
RANGE
SELECT
AND GAIN
CONTROL
2.5V
BANDGAP
REFERENCE
2.2μF
TIE TO VDD TO USE
INTERNAL 2.5V
REFERENCE
OR INPUT FOR
EXTERNAL 2.5V
REFERENCE
OR INPUT FOR
EXTERNAL 1.25V
REFERENCE
2274 F06
LTC2274
Figure 6. Reference Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2285IUP#3CGPBF | PROPRIETARY METHOD ADC, PQCC64 |
| LTC2305CDE#PBF | 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO12 |
| LTC2305CMS#PBF | 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO12 |
| LTC2305IDE#PBF | 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO12 |
| LTC2305IDE#TRPBF | 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO12 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2274IUJ#PBF | 制造商:Linear Technology 功能描述:ADC Single Pipelined 105Msps 16-bit Serial 40-Pin QFN EP 制造商:Linear Technology 功能描述:IC ADC 16-BIT 105MSPS 40-QFN 制造商:Linear Technology 功能描述:IC ADC 16BIT 105MSPS QFN-40 制造商:Linear Technology 功能描述:IC, ADC, 16BIT, 105MSPS, QFN-40; Resolution (Bits):16bit; Sampling Rate:105MSPS; Supply Voltage Type:Single; Supply Voltage Min:3.135V; Supply Voltage Max:3.465V; Supply Current:394mA; Digital IC Case Style:QFN; No. of Pins:40 ;RoHS Compliant: Yes |
| LTC2274IUJ#TRPBF | 制造商:Linear Technology 功能描述:ADC Single Pipelined 105Msps 16-bit Serial 40-Pin QFN EP T/R 制造商:Linear Technology 功能描述:IC ADC 16-BIT 105MSPS 40-QFN |
| LTC2274IUJ-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:16-Bit, 105Msps Serial Output ADC |
| LTC2274IUJ-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:16-Bit, 105Msps Serial Output ADC |
| LTC2274IUJ-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:16-Bit, 105Msps Serial Output ADC |
發布緊急采購，3分鐘左右您將得到回復。