參數資料
型號： LTC1967IMS8#TRPBF
廠商： Linear Technology
文件頁數： 13/28頁
文件大?。?/td> 327K
描述： IC CONVERTER RMS-DC PREC 8MSOP
標準包裝： 2,500
電流 - 電源： 320µA
電源電壓： 4.5 V ~ 5.5 V
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 帶卷 (TR)
13
LTC1967
1967f
Output Connections
The LTC1967 output is differentially, but not symmetri-
cally, generated. That is to say, the RMS value that the
LTC1967 computes will be generated on the output (Pin 5)
relative to the output return (Pin 6), but these two pins are
not interchangeable. For most applications, Pin 6 will be
tied to ground (Pin 1). However, Pin 6 can be tied to any
voltage between 0V and V
+
 (Pin 7) less the maximum
output voltage swing desired. This last restriction keeps
V
OUT
 itself (Pin 5) within the range of 0V to V
+
. If a
reference level other than ground is used, it should be a
low impedance, both AC and DC, for proper operation of
the LTC1967.
In any configuration, the averaging capacitor should be
connected between Pins 5 and 6. The LTC1967 RMS-DC
output will be a positive voltage created at V
OUT
 (Pin 5)
with respect to OUT RTN (Pin 6).
Power Supply Bypassing
The LTC1967 is a switched capacitor device, and large
transient power supply currents will be drawn as the
switching occurs. For reliable operation, standard power
supply bypassing must be included. A 0.01礔 capacitor
from V
+
 (Pin 7) to GND (Pin1) located close to the device
will suffice. If there is a good quality ground plane avail-
able, the capacitors can go directly to that instead. Power
supply bypass capacitors can, of course, be inexpensive
ceramic types.
Up and Running!
If you have followed along this far, you should have the
LTC1967 up and running by now! Dont forget to enable
the device by grounding Pin 8, or driving it with a logic low.
Keep in mind that the LTC1967 output impedance is fairly
high, and that even the standard 10M& input impedance
of a digital multimeter (DMM) or a 10?scope probe will load
down the output enough to degrade its typical gain error
of 0.1%. In the end application circuit, either a buffer or
another component with an extremely high input imped-
ance (such as a dual slope integrating ADC) should be used.
APPLICATIO S I FOR ATIO
U
U
U
For laboratory evaluation, it may suffice to use a bench-top
DMM with the ability to disconnect the 10M& shunt.
If you are still having trouble, it may be helpful to skip
ahead a few pages and review the Troubleshooting Guide.
What About Response Time?
With a large value averaging capacitor, the LTC1967 can
easily perform RMS-to-DC conversion on low frequency
signals. It compares quite favorably in this regard to prior-
generation products because nothing about the ?/DIV>
circuitry is temperature sensitive. So the RMS result
doesnt get distorted by signal driven thermal fluctuations
like a log-antilog circuit output does.
However, using large value capacitors results in a slow
response time. Figure 10 shows the rising and falling step
responses with a 1礔 averaging capacitor. Although they
both appear at first glance to be standard exponential-
decay type settling, they are not. This is due to the
nonlinear nature of an RMS-to-DC calculation. Also note
the change in the time scale between the two; the rising
edge is more than twice as fast to settle to a given
accuracy. Again this is a necessary consequence of RMS-
to-DC calculation.
3
Although shown with a step change between 0mV and
100mV, the same response shapes will occur with the
LTC1967 for ANY step size. This is in marked contrast to
prior generation log/antilog RMS-to-DC converters, whose
averaging time constants are dependent on the signal
level, resulting in excruciatingly long waits for the output
to go to zero.
The shape of the rising and falling edges will be dependent
on the total percent change in the step, but for less than the
100% changes shown in Figure 10, the responses will be
less distorted and more like a standard exponential decay.
For example, when the input amplitude is changed from
3
 To convince oneself of this necessity, consider a pulse train of 50% duty cycle between 0mV and
100mV. At very low frequencies, the LTC1967 will essentially track the input. But as the input
frequency is increased, the average result will converge to the RMS value of the input. If the rise and
fall characteristics were symmetrical, the output would converge to 50mV. In fact though, the RMS
value of a 100mV DC-coupled 50% duty cycle pulse train is 70.71mV, which the asymmetrical rise
and fall characteristics will converge to as the input frequency is increased.
相關PDF資料
PDF描述
LTC1968IMS8#TRPBF IC CONVERTER RMS-DC PREC 8MSOP
LTC3100EUD#TRPBF IC REG BUCK/BOOST/LINEAR 16-QFN
LTC3104IMSE#TRPBF IC REG DL BCK/LINEAR SYNC 16MSOP
LTC3445EUF#TRPBF IC REG TRPL BUCK/LINEAR 24-QFN
LTC3446IDE#PBF IC REG TRPL BCK/LINEAR 14-DFN
相關代理商/技術參數
參數描述
LTC1968CMS8 功能描述:IC CONVERTER RMS-DC PREC 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - RMS 至 DC 轉換器 系列:- 標準包裝:46 系列:- 電流 - 電源:1.2mA 電源電壓:±18 V，36 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC W 包裝:管件
LTC1968CMS8#PBF 功能描述:IC CONVERTER RMS-DC PREC 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - RMS 至 DC 轉換器 系列:- 標準包裝:46 系列:- 電流 - 電源:1.2mA 電源電壓:±18 V，36 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC W 包裝:管件
LTC1968CMS8#TR 功能描述:IC CONVERTER RMS-DC PREC 8MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - RMS 至 DC 轉換器 系列:- 標準包裝:46 系列:- 電流 - 電源:1.2mA 電源電壓:±18 V，36 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC W 包裝:管件
LTC1968CMS8#TRPBF 功能描述:IC CONVERTER RMS-DC PREC 8MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - RMS 至 DC 轉換器 系列:- 標準包裝:46 系列:- 電流 - 電源:1.2mA 電源電壓:±18 V，36 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC W 包裝:管件
LTC1968CMS8PBF 制造商:Linear Technology 功能描述:RMS-to-DC Converter Prec. 500kHz MSOP8
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*