- 您現在的位置：買賣IC網 > PDF目錄377746 > LTC1415ISW (LINEAR TECHNOLOGY CORP) 12-Bit, 1.25Msps, 55mW Sampling A/D Converter PDF資料下載
參數資料
| 型號： | LTC1415ISW |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 12-Bit, 1.25Msps, 55mW Sampling A/D Converter |
| 中文描述： | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO28 |
| 封裝： | 0.300 INCH, PLASTIC, SO-28 |
| 文件頁數： | 8/24頁 |
| 文件大?。?/td> | 481K |
| 代理商： | LTC1415ISW |
8
LTC1415
APPLICATIO
S I
N
FOR
ATIO
U
CONVERSION DETAILS
The LTC1415 uses a successive approximation algorithm
and an internal sample-and-hold circuit to convert an
analog signal to a 12-bit parallel output. The ADC is
complete with a precision reference and an internal clock.
The control logic provides easy interface to microproces-
sors and DSPs (please refer to Digital Interface section for
the data format).
Conversion start is controlled by the CS and CONVST
inputs. At the start of the conversion the successive
approximation register (SAR) is reset. Once a conversion
cycle has begun it cannot be restarted.
During the conversion, the internal differential 12-bit
capacitive DAC output is sequenced by the SAR from the
most significant bit (MSB) to the least significant bit (LSB).
Referring to Figure 1, the +A
IN
and –A
IN
inputs are con-
nected to the sample-and-hold capacitors (C
SAMPLE
) dur-
ing the acquire phase and the comparator offset is nulled by
the zeroing switches. In this acquire phase, a minimum
delay of 150ns will provide enough time for the sample-
and-hold capacitors to acquire the analog signal. During
the convert phase the comparator zeroing switches open,
putting the comparator into compare mode. The input
switches the connect C
SAMPLE
capacitors to ground, trans-
ferring the differential analog input charge onto the sum-
ming junction. This input charge is successively compared
W
U
with the binary weighted charges supplied by the differen-
tial capacitive DAC. Bit decisions are made by the high
speed comparator. At the end of a conversion, the differ-
ential DAC output balances the +A
IN
and – A
IN
input
charges. The SAR contents (a 12-bit data word) which
represents the difference of +A
IN
and –A
IN
are loaded into
the 12-bit output latches.
DYNAMIC PERFORMANCE
The LTC1415 has excellent high speed sampling capabil-
ity. FFT (Fast Fourier Transform) test techniques are used
to test the ADC’s frequency response, distortion and noise
at the rated throughput. By applying a low distortion sine
wave and analyzing the digital output using a FFT algo-
rithm, the ADC’s spectral content can be examined for
frequencies outside the fundamental. Figure 2 shows a
typical LTC1415 FFT plot.
Figure 1. Simplified Block Diagram
COMP
+C
SAMPLE
–C
DAC
D11
D0
ZEROING SWITCHES
HOLD
HOLD
+A
IN
–A
IN
+C
DAC
–C
SAMPLE
12
LTC1415 F01
+
–
SAR
OUTPUT
LATCHES
+V
DAC
–V
DAC
HOLD
HOLD
SAMPLE
SAMPLE
FREQUENCY (kHz)
0
A
0
–20
–40
–60
–80
–100
–120
100
200
300
400
LTC1415 F02
500
600
f
SAMPLE
= 1.25MHz
f
= 99.792kHz
SFDR - 87.5
SINAD = 72.1
Figure 2. LTC1415 Nonaveraged, 4096 Point FFT
Signal-to-Noise Ratio
The signal-to-noise plus distortion ratio [S/(N + D)] or
SINAD is the ratio between the RMS amplitude of the
fundamental input frequency to the RMS amplitude of all
other frequency components at the A/D output. The output
is band limited to frequencies from above DC and below
half the sampling frequency. Figure 2 shows a typical
spectral content with a 1.25MHz sampling rate and a
100kHz input. The dynamic performance is excellent for
input frequencies up to the Nyquist limit of 625kHz.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1416IG | Low Power 14-Bit, 400ksps Sampling ADC |
| LTC1416 | Low Power 14-Bit, 400ksps Sampling ADC |
| LTC1416CG | Dual, Low Voltage, LinCMOS(TM) Differential Comparator 8-SOIC -40 to 85 |
| LTC1417ACGN | Dual, Low Voltage, LinCMOS(TM) Differential Comparator 8-PDIP -40 to 85 |
| LTC1417 | Low Power 14-Bit, 400ksps Sampling ADC Converter with Serial I/O |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1415ISW#PBF | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1415ISW#TR | 功能描述:IC ADC 12BIT 1.25MSPS SMP 28SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1415ISW#TRPBF | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1416CG | 功能描述:IC A/D CONV 14BIT SAMPLNG 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1416CG#PBF | 功能描述:IC A/D CONV 14BIT SAMPLNG 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。