- 您現在的位置：買賣IC網 > PDF目錄369814 > LPC3180 (NXP Semiconductors N.V.) 16/32-bit ARM microcontroller; hardware floating-point coprocessor, USB On-The-Go, and SDRAM memory interface PDF資料下載
參數資料
| 型號： | LPC3180 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 16/32-bit ARM microcontroller; hardware floating-point coprocessor, USB On-The-Go, and SDRAM memory interface |
| 中文描述： | 16/32位ARM微控制器，硬件的浮點協處理器的USB On - The - Go的，和SDRAM存儲器接口 |
| 文件頁數： | 25/36頁 |
| 文件大?。?/td> | 188K |
| 代理商： | LPC3180 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LPC3180_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Preliminary data sheet
Rev. 01 — 2 June 2006
25 of 36
Philips Semiconductors
LPC3180
16/32-bit ARM microcontroller with external memory interface
6.23 Reset
Reset is accomplished by an active low signal on the RESET_N input pin. A reset pulse
with a minimum width of 10 main oscillator clocks after the oscillator is stable is required to
guarantee a valid chip reset. At power-up, 10 milliseconds should be allowed for the
oscillator to start up and stabilize after V
DD
reaches operational voltage. An internal reset
with a minimum duration of 10 clock pulses will also be applied if the watchdog timer
generates an internal device reset.
6.24 Clocking and power control
Clocking in the LPC3180 is designed to be versatile, so that system and peripheral
requirements may be met, while allowing optimization of power consumption. Clocks to
most functions may be turned off if not needed, some peripherals do this automatically.
The LPC3180 includes three operational modes that give control over processing speed
and power consumption. In addition, clock rates to different functional blocks may be
controlled by changing clock sources, reconfiguring PLL values, or altering clock divider
configurations. This allows a trade-off of power versus processing speed based on
application requirements.
6.24.1
Crystal oscillator
The main oscillator is the basis for the clocks most chip functions use by default.
Optionally, many functions can be clocked instead by the output of a PLL (with a fixed
397x rate multiplication) which runs from the RTC oscillator. In this mode, the main
oscillator may be turned off unless the USB interface is enabled. If a SYSCLK frequency
other than 13 MHz is required in the application, or if the USB block is not used, the main
oscillator may be used with a frequency of between 1 MHz and 20 MHz.
6.24.2
PLLs
The LPC3180 includes three PLLs: one allows boosting the RTC frequency to
13.008896 MHz for use as the primary system clock; one provides the 48 MHz clock
required by the USB block; and one provides the basis for the CPU clock, the AHB bus
clock, and the main peripheral clock.
The first PLL multiplies the 32768 Hz RTC clock by 397 to obtain a 13.008896 MHz clock.
The 397x PLL is designed for low power operation and low jitter. This PLL requires an
external RC loop filter for proper operation.
The other two PLLs accept an input clock from either the main oscillator or the output of
the 397x PLL. The input frequency is multiplied up to a higher frequency, then divided
down to provide the output clock.
The PLL input may initially be divided down by a pre-divider value ‘N’, which may have the
values 1, 2, 3, or 4. This pre-divider can allow a greater number of possibilities for the
output frequency.
Following the PLL input divider is the PLL multiplier. This can multiply the pre-divider
output by a value ‘M’, in the range of 1 through 256. The resulting frequency must be in
the range of 156 MHz to 320 MHz. The multiplier works by dividing the output of a Current
Controlled Oscillator (CCO) by the value of M, then using a phase detector to compare the
divided CCO output to the pre-divider output. The error value is used to adjust the CCO
frequency.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC61W26X | Microcontroller |
| LPC61W49X | Microcontroller |
| LPC660AIMX | Voltage-Feedback Operational Amplifier |
| LPC660IMX | Voltage-Feedback Operational Amplifier |
| LPC661IMX | Voltage-Feedback Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC3180-DEV-KIT | 功能描述:開發板和工具包 - ARM LPC3180 Dev Kit RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| LPC3180FEL320 | 功能描述:IC ARM9 MCU 208MHZ 320-LFBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:LPC3100 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| LPC3180FEL320,551 | 功能描述:ARM微控制器 - MCU ARM9 FLTNG PNT CO-PR FLTNG POINT CO-PROC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC3180FEL320/01 | 制造商:NXP Semiconductors 功能描述:MCU 16-Bit/32-Bit LPC3100 ARM926EJ-S RISC ROMLess 1.2V/1.8V/3.3V 320-Pin LFBGA Tray |
| LPC3180FEL320/01,5 | 功能描述:ARM微控制器 - MCU ARM9 64KRAM VFP USB OTG BGA320 RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。